DSD TECHSH-U09C USB to TTL Serial Adapter with FTDI FT232RL Chip Compatible with Windows Mac Linux

Worked straight away out of the box. It provides enough power to run a STM32 micro controller. The cable is of a decent quality and is long enough for the purpose.

I recently purchased the DSD TECH USB to TTL Serial adapter with FTDI FT232RL Chip from Amazon, and I must say that I am highly impressed with the quality of this product. This adapter is far superior to similar products due to its transparent case, which not only looks great but also protects the adapter from wear and tear over time.What sets this adapter apart from competitors is its unique casing – most other adapters do not come with a case, leaving them vulnerable to damage from everyday use. This is especially true if you use the adapter regularly, as exposure to the elements can cause damage to the internal components of the adapter. The DSD TECH USB to TTL Serial adapter's casing provides excellent protection against this, ensuring that your adapter will last for a long time.Another great feature of this adapter is that it comes with connection cables and a voltage changer. The voltage changer enables you to switch between 3.3v and 5v, which is highly useful if you are working with different types of devices or electronics. Additionally, the included cables make it easy to connect to any USB-enabled device.Overall, I would highly recommend the DSD TECH USB to TTL Serial adapter with FTDI FT232RL Chip to anyone who works with electronics on a regular basis. The quality of the product is exceptional, and the included features make this adapter stand out from the rest. Whether you are a professional or a hobbyist, this adapter will meet all of your needs and expectations.

I really like this USB to TTL serial converter, well designed. Works great as an ATmega328 programmer. Works from the Arduino IDE. I had to install the driver, was easy to do.If you are new to the Arduino prototyping platform make sure you connect a 16MHz crystal, 22pf load capacitors and a resistor to the chip if you are using a breadboard project. There are diagrams online. With the connections some schematics refer to DTR, this is the same ad RTS with this module.

Nice to see a little bit of thought has gone into this. The case is clear so that you can see the pin assignments which are printed on both sides of the PCB.No extra drivers needed by OSX the device is detected automatically.Works with ESP32 Devkit (use 5v and plug VCC into 5v pin on ESP32) even with wifi/bt enabled. When uploading hold both EN and BOOT buttons when you see the ....___.... release EN. Once the upload begins release BOOT.

Works perfectly to flash esp chips on OSX Big Sur, very nice packaging, though needs removal from case and case modification to access some pinouts (DTR, for example). 3.3v VCC is steady and has been sufficient to supply esp01/07 programming and esp32 development boards.

Worked perfectly straight out of the box - bought other cheap ones on Amazon but had to return due to failing to work.Was successfully able to connect to a device via UART.No drivers required to be downloaded for either Windows 11 or Raspbian.

A good compromise between the unreliable cheap ftdi devices and the expensive units available from FTDI themselves. It comes with a six wire connector (seen in the 5th photo on this page) and a tiny manual in 7 languages. Selectable 3.3 or 5 volts.It has an two unpopulated rows of connectors giving access to other serial control pins. If you need these then you can get the case apart and solder header pins on or just solder a single wire if that's all you need.The device comes with two jumpers, one to select 3,3 or 5 volts and the other so you can test by connecting tx to rx.If TTL data is being sent to the device but not being read from the USB port then the data lights will not flash.I am using this with a GPS module and a wire soldered to the DSD pad to provide a Linux PC with a time signal including Pulse Per Second.Also consider from Amazon the a similar device but with a wider range of voltages and signal pins, the DSD TECH SH-U09C5 USB to TTL UART Converter Cable with FTDI Chip Support 5V 3.3V 2.5V 1.8V TTL.

I bought this to flash the SONOFF Zigbee Hub with Tasmota and it flashed it with no problems. The jumper on mine came set to 3.3v but make sure you check this before you try to flash anything.It does come with M (USB adapter) > F dupont cables.However just a heads up, to flash the SONOFF I needed male to go through the holes on the SONOFF PCB so I bought some dupont cables off ebay but they were slightly too big to go through the holes in the PCB. I ended up using the individual solid cores from a CAT6 cable and these were quite a good fit.