AB Wall-mounted Radiator Heater with 8 Panels, Light Weight Aluminum Hot Water Radiator for Kitchen, Bedroom and Greenhouse…

Follow the tips in other reviews about tightening and sealing, measure carefully, and be careful with seating the threads and the hangers, and it will be fine. It makes a lot of heat for its size because of the clever fin design, and looks better in most rooms than traditional big iron radiators.

The reason I got this radiator was because the wife wanted one in a tiny bathroom, i didn't want to plunk the usual cast iron radiator in there, so i got this one off amazon. Cheap and delivered next day. Biggest downsides are the quality of the cut on their bushings, and the mounting hooks, but both are easily remedied. Overall a great buy. Im a contractor, so ill give you guys a hand, as the instructions were pretty minimal. It did take some wrangling to get everything set in place and sealed up. Also, of you need more instructions than what i'm giving, i almost want to say you should call a plumber... its a standard radiator install. First off, this radiator is not American designed or made. The threading on it is something I've never heard of. But, not to worry, they give you bushings that convert all four outlets to 3/4 inch NPT. (This is not mentioned anywhere). You can see in the pics, i had no trouble hooking it up to standard 3/4 inch radiator spuds. Lay the thing down on carpet and grab a crescent wrench. Now check the bushings. They all have an o-ring on them, but they need thread tape as well. Make sure the o rings are straight and seated properly. For tape, they give you some (cheap weird foreign tape i've never seen before), toss it in the trash and go get some normal teflon tape, or better yet the high end expensive thread tape. Put about triple the tape you normally would on the bushings. I wrapped them 10x each, that seemed to do it. Make sure you aren't wrapping the o ring and trapping it. Once wrapped, thread in the bushings, and get those suckers in just about as tight as you can. Then tighter. This is why you do it on the floor, if you aren't ripping the hooks off the wall it isn't tight enough. For the left side, the bushings are reverse threaded, so the bottom left needs to be even tighter. Just extremely, excessively, tight. That one, when you go to thread in your spud, is going to want to back out because of the reverse threading. Also make sure to tape the left ones in reverse. Next, put your spuds in, or whatever you're connecting it to. You also need triple the normal tape on your npt threads, the bushing they give you is just not a good cut. So 10+ wraps. Get those in also pretty good and tight. They give you a cap.and a bleeder for the top. Next, line it up and mark the wall for your mounts. The mounts are just hooks that it hangs on. You need to make sure they're lined up perfectly to fit through the fins in the back. Also, as you can see from my picture, the mounts arent designed for drywall. So i would recommend putting some blocking behind it, i'm going to have to redo that. Hook your unions up and you should be good to go. I did have to redo mine due to leaks at my fittings. If you follow my instructions, you wont have to. Great buy.

DO NOT BUY. It technically works, but despite professional installation, it still leaks due to low quality parts. It does not output very much heat. I’d recommend consulting your local plumbing supply store for better options. They will probably cost a bit more, but you’ll be better off.

So far so good. Will update in a few months

This is a good panel. It replaced a bigger cast iron radiator, Obviously its not as good but we never needed that much to begin with. I'd say I get about 2500 btu out of it and i don't think I could a bit more. It's shape does add a heat spreading effect that is nice, It was easy to install. It's been great for a few years now.

Not as much heat output as I would like. Changeable plugs for water flow were not taped right retapped them it did not make a difference, had to use a lot of dope and tape to get one of the hole to seal. Looks nice, poor quality control

Had no issues with unit easy to install. One elbow leaked but that was my fault did not use enough tape and did not tighten it enough. I used pex 3/4 elbows (bought on Amazon $11 for 2) so it was easy enough to take apart. Important tips: 1. Tape the nipples exactly ten times like the other review said. 2. Use blocking for mounts, drill a hole tap in the sleeve and then screw in the hook.(mounts are not for drywall) 3. The nipples only fit in their corresponding holes.

purchased this item to replace a worn out radiator. it is lightweight which made easier to install. It is a little larger than I would like, but works well and the price was very good.

Need a few things not included to link to my heating pipes. Will have to call a plumber. Not so much DIY. Otherwise great product as described.

This unit was purchased at a reasonable price just to take the chill out of a larger room. It manages to do it.

Blasts heat almost instantly and has a really nice neat/minimalist look that blends into most any room. Also appreciate that they now ship with NPT (National Pipe Thread) inserts and I don't have to look for BSPT (British Standard Pipe Taper) to NPT adapters. Only gripe is that the mounting system (hooks) are dependent on fitting between the fins of the rad, and don't properly line up at 16" on center (North American studding dimensions). Someone should really think of a better system that is adjustable and doesn't just have the rads hanging on hooks like a fishing rod on the wall of a shed.

Works well in the chicken coop for heat.