Dryer Repair Kit Contains 279311 Igniter 279834 Gas Valve Coil 338906 Flame Sensor Fit for Kenmore Whirlpool Maytag Gas Dryers

Short story. I have a Whirlpool gas dryer that is an older model (over 20 years old) and the flames wasn't blowing out to heat the unit, however the igniter is burning red. I actually bought the package that includes the Thermal Cut-Off Kit, Thermostat, and Thermal Fuse. After watching a bunch of DYI videos on YouTube, I replaced all these parts in my unit. Turned out the issue with my gas dryer not blowing flames wasn't caused by these parts. However, since I've already replaced them and my unit is over 20 years old, I decided the leave them there. After further troubleshooting, I found I needed to replace the Gas Valve Coil and Flame Sensor so I bought these. It's exactly what I needed and completely fixed the issue. I had absolutely no experience installing any of these, so I watched a bunch of DYI YouTube videos explaining how to install these and I was golden. I was able to install them on the first try. Saved me so much money having to call a pro repair man to come to install these. However, one thing to note is the ignitor is extremely brittle. All I was doing was tightening the screw on the housing compartment and the right side of the ignitor snapped off. After carefully checking for a reason, it wasn't touching anything or scrapping off the sides of anything so there was no reason for it to break off. Perhaps I was tightening the screw too hard but the video I was watching said to tighten it like that. Luckily for me, my old ignitor that came with the unit was still usable so I put it back in its place. The was able to install the Gas Valve Coil and the Flame Sensor without any issue. They were actually really easy to install. The Gas Valve Coil and Flame Sensor was what fixed the issue for me. Now my 20+ years gas dryer is working like new. So to summarize, if you see the igniter is red but no flames are coming out, or the flames blowing but only for the first cycle (the flames comes out in cycles or intervals, meaning every 5 minutes or so gas will flow out causing the igniter to burn it so it's not a continuous stream of flame), then it completely stop when there are wet clothes in the dryer then buying these (in particular the Gas Valve Coil and Flame Sensor will fix your issue. It did for me. I highly recommend buying these!

This kit had all the parts needed to repair the burner on my gas dryer and was reasonably priced. The parts are of good quality and an exact match. The repair was medium difficulty because of having to take off the top and front of the machine, but not too bad. Wish I had checked the fuse at the inside rear of the machine first, however. Turns out that little $2 fuse was the problem so I replaced these burner parts on the front side for no reason, and the dryer still didn’t heat. Replacing the fuse is much simpler, and now the dryer runs great! If you need to fix the burner, this kit has what you need , but strongly suggest checking the fuse and other back of machine parts first.

Got my dryer working again and for a fraction of the cost of manufacturer parts.

Used to repair whirlpool dryer and it worked fine.

Parts all fit a Kenmore gas dryer and seemed equivalent to the original parts. The ignitor, however, broke. I read reviews that it was brittle and handled it with great care, not touching the element, and installed. First start it did not even glow, so I took things apart and saw it was broken. I reinstalled the original ignitor and thankfully it worked/was not the original problem (which I was having trouble diagnosing). After it cooled, the ignitor just broke in pieces with little pressure. So it is really brittle. I don't know if it broke on its own or if even being careful I broke it - and whether there are better ignitors out there, but ultimately it did not work for me.

exelente producto

Do NOT buy! Absolute garbage, failed on first use. Our Whirlpool Duet was not heating up so replaced the igniter and other parts in the kit. There was no glow of the igniter before parts replacement so I got exicted when starting the dryer after replacing parts because I saw the igniter glow and thought the dryer was back in business. However, before the gas would start to flow, the igniter fell into pieces into the fire tube, bits and pieces still glowing for a while. Needless to say I was not happy. Ended up putting the old igniter back, which worked fine, so it must have been some of the other parts that were at fault, probably the solenoids / gas valves. I'd return the whole kit, but don't want to go thru the labor of doing everything all over again. Maybe I should, now I wonder about the quality of the rest of the parts in the kit. Time will tell, but I'll never buy anything from this manufacturer again. I'd give zero stars if I could, buyer beware, do NOT buy this garbage.

Dryer wouldn't run... Installed these parts and now it fires right up, no pun intended. Easy to install, just be sure you know how to disassemble your dryer and locate the replacement part location. Direct replacement. Thanks for the kit.