KXZM DC 5V USB COB LED Strip Light Cool White 6000K Dimmable IP65 Waterproof CRI 93+ USB Powered 6.6ft/2M 640LEDs with Dimmer High Brightness Flexible LED Tape Lights

Works and powers great. Very durable outside. Super visible at night. No control is needed but that is its purpose for simplifying DIY projects. The COB silicone is easy to scrub off, just make sure to scrape off the coating on the copper pads if you’re going to solder to it.

Very bright and the light is uniform/consistent

Lined the inside of my electric bike frame with these green lights, used 3 strips and about 15 feet in total. I also used double sided nano tape I ordered, to easily install these led strips onto the bike frame. Nice and bright!

Purchased once before and had a good experience with these lights however the second time around wasn't as good. The adhesive on the strips was not protected and came damaged and when I contacted amazon for help they didn't really offer much that worked with my time frame. The seller however came in clutch and helped me and I really appreciate that. Other than the adhesive issue the lights worked great for my project.

These lights are very bright and seem to be good quality. However, the adhesive has a MAJOR flaw, so make sure you read this...When you are ready to apply the light strip to a surface and go to peel off the paper backing, make sure the adhesive is sticking to the light strip and NOT the paper you are peeling off! This is very difficult to do, because the adhesive has a stronger bond to the paper than it does to the back of the light strip, and once you peel the paper off, there is virtually no way to get the adhesive back onto the light strip. My recommendation: don't start peeling at either end of the strip. Instead, find a place along the strip where the paper-backing is buckling and sticking up. Then use the tip of a knife to cut the paper and carefully peel away the paper from that spot while making sure the adhesive is on the light strip. If you do this, you're good to go. Good luck!

This was my first COB light application, and I've had sketchy LED troubles before. This product PERFORMS, and continues to do so! It lights up the space I need extremely brightly, has a simple power solution, and has an excellent reputation for use in lightboxes. Looking forward to more units and more successes!

Worked perfectly. Not sure for how long but it was under $3. It is designed for indoor use but for $3, who cares if it lasts only a month or two. I used it as underglow lights on a go kart that.never sees inclement weather or moisture. Liked it so much I may get one for my TV. The controller has so many options, it makes it hard to do anything special with it but again, for $3, who cares.

I give three stars because, although the LED lights themselves work nicely and are a pleasant sight to behold when turned on, there was a problem with the glue on the back. Like most self-stick products, the strip comes with a wax-paper backing material that you are supposed to peel off to expose the sticky surface. However, when I peeled off the wax paper, all of the glue stuck to the wax paper instead of the light strip! So the back of the light strip had no adhesive and would not stick to anything. I solved the problem by using double-stick Scotch tape for mounting, but this should not have been necessary to do.

Not really orange in colour

So my main gripe with this is that the pictures don't exactly match the product; there is no silicone over top of the entire surface, only the silicone used as the LED COB itself. I went into this knowing that might be a risk (I forgot to look at other review photos, silly me) but it's still disappointing. Bare copper is exposed at regular intervals along the length of the strip, so if this is a concern for you, aim for something IP68 rated. Anyway, some helpful info: For the entire 2m length, power draw at 5.0V is just shy of 2.0A (10W). Most of my USB power supplies drop voltage a bit at this load and end up supplying 4.8V at 1.6A (despite claiming 2.4A capacity; shoddy power supplies I guess, not a dig at the LED strip). If you're using this as a light strip in a Bambu Lab X1/P1 series printer, be aware the built-in USB outlet only provides 1.5A, and so the strip should be cut to a maximum length of 1.5m.

It was on fire while I was charging it