Delta Windemere Oil Rubbed Bronze Kitchen Faucet with Side Sprayer, Traditional 4 Hole Kitchen Sink Faucet, Two-Handle, Oil Rubbed Bronze 21996LF-OB

Great looking, it has good pressure and the sprayer function well. Good quality and assembly. Great value and the temperature control is great

I love this piece. It was so easy to install. It is made well and sturdy. i have a home where we cook all meals. The sink gets USED. Especially with 3 teens - holds up and looks great!

Pros: Cheap ($70 at the time of purchase), works, looks good, mostly metal, readily available repair parts Cons: Handles wobble a bit, modest water flow, sprayer is all plastic. Bottom line: A decent cheap utility room or economy kitchen faucet. I would prefer a bit higher water flow, but it is good enough. The build quality is decent, not as good as more expensive Deltas, but not as bad as many similar priced off brand faucets, and there are readily available repair parts. The valve kit for this faucet is the Peerless #RP54801 (delta's off brand). This is cheap ($70 at the time) for a Delta faucet. The main reason to buy a Delta is that you can get low cost repair parts for all of the pieces that are likely to fail. I have some delta faucets that I have kept working now for 15+ years by replacing the valves a couple of times. Delta tends to reuse the same internals for many years, so you can usually keep getting parts for a faucet long after the model that you bought is no longer made. I bought this to replace a Danze faucet at my utility sink that suddenly failed, it was one of those with lifetime ceramic valves, so there was no way to repair it or even take it apart to see what was wrong with it. Delta's may not last as long as some of the other premium bands and they cost more then some off brands, but they are easy to repair. It only takes me like 15 min to swap out the valves in a Delta, while if something goes wrong with another brand I have to replace the whole facet. So in the long run I believe that Deltas are both cheaper and less trouble then other brands because you can just keep them working almost indefinably using $15 repair kits every 2-7 years.

I bought this faucet nearly two years ago but only got around to installing it a few days ago. Installation went well. The faucet works OK but, for some reason I have not figured out, it makes a fairly loud "thud" noise when the water is turned on, hot or cold, it makes no difference. If the valves are opened very slowly the thud doesn't occur right away and, if left at a very low flow setting, it might not occur at all but, if the valve is opened further, no matter how gradually, the thud noise will eventually occur. I've never experienced any faucet behaving this way so it makes me a little nervous. Hopefully it's not an indication of something on the verge of failure. The other thing that worries me about this faucet is the flimsiness. The stem assemblies are not at all rigid, they're really flimsy and deflect quite noticably when operating the valves. I worry that the repeated bending that's taking place each time the valves are operated will eventually lead to failure. Based on my previous experience with Delta faucets (all manfactured years, if not decades, earlier than this one) I am very surprised and disappointed in how flimsy this faucet seems to be. I chose this faucet primarily because of my great experience with Delta faucets over the past 50 years or so. The old Delta kitchen faucet that I replaced with this one dates back to 1989 and was built like a tank. It was heavy cast brass construction. This new one seems to be mostly foil thin metal that is reinforced by lightweight plastic. I seriously doubt this new faucet is going to last 33 plus years like the old one did. I'm a little sad about that, especially considering the cost of these things and the hassle of replacing them. Would I buy this faucet again? I can't answer that question yet. We'll have to see how it performs over time. My wife and I do both like the looks of it and we like the higher spiggot and the fact that the spiggot is easier to swing than the one on the old faucet was so it does have those things going for it.

Super easy to install and worked perfect. It feels light and is probably plastic, but overall and for the price it was perfect for our use. I would buy again.

Looks good and works well. It is easy to clean and has good water flow.

I most extremely nice

Plumber has no trouble at all. Good price, good pressure, looks good, love the sprayer.

Good looking faucet. Well made for the price. Not sure what parts people believe are plastic outside of the side sprayer. For an inexpensive two handle faucet you cannot go wrong. Handles are 1/4 turn and are very smooth. Water flow is just fine (home has good water pressure). I found it super easy to install once I was able to rid myself of the last home owners messed up installation of the previous faucet. I was able to connect a portable dishwasher. This adapter https://www.amazon.ca/dp/B0058G1JUG is necessary to change thread sizes in order to connect dishwasher fitting.

I got this faucet for my cabin where water pressure can be a bit low. The two handle design with 1/2" connections is ideal for limiting flow restriction. This was a huge improvement over my old one handle faucet. It was super easy to install. Some of the materials feel a bit cheap but I think that should be expected for the price of this faucet. I highly recommend.

Nice taps but they bang nearly every time I turn them on. I don't think it will hurt them, it is just a nuisance.

Having trouble finding a portable dishwasher attachment. Otherwise I really like it. I was easy to install and sturdy. Looks great with the new sink.

Très belle qualité design moderne