MF2720 Ultra Slim Fixed TV Wall Bracket for 17-27 inch LED/LCD/OLED/Plasma Flat & Curved TVs up to 15kg with Max VESA 100x100 mm

They appear to be sturdy enough. I bought 2 for some 22” monitors, stability is fine and being small they fit just where I need them, very easy to use, just pop some screws into the back plate on a wall. Then screw in the front part to the back of your monitor. Finally just slide the monitor onto the part on the wall.

I've fitted a few TV brackets but this one tops them all, it's cheap basic, simple to fit and rock solid once fitted.

I wanted a small flush bracket for a 32'' Bedroom TV in small room which has limited space for an arm bracket. This is very simple and easy to mount with a wall drill.However TV so tight to the wall I cant fit an ariel plug and its hard to plug in the power and HDMI once the TV is on the wall.So its fine for a TV where you can leave the HDMI connection in and you don't need an ariel.Suits TVs with sockets on side of TV not on rear of TV so beware.Also TV drops into bracket so you need a lot of play above the TV to drop it in so not much use tight under a shelf. I had to remove the shelf above to fit the TV then put the shelf back afterwards. So ideal in certain situations but think before you buy it may not suit your room.

Great purchase. Absolute bargain for the price and easy to fit with a variety of screws to ensue you have some that fit. Can’t fault this purchase at all

Happy w my purchase, it holds the TV against a wall and if like me this is all you need, no swivel, then you won't go wrong

The mount isn’t a very snug fit, so when you slide the monitor attached piece into the wall mounted piece, there’s enough of a gap between the two pieces to allow for slightly heavier monitors or TVs to lean forwards. This would be fixed if the gap you slide the monitors into was more of a snug fit. There are better mounts available at this price

Good value.

The dovetails are very loose so it installs fairly easily but isn't rock solid until you add the screws in from the bottom. These are listed on the instructions as M4x10 and the screws supplied are M4. Problem is that the holes are more like M3.5 - which is the size of screw used in UK electrical sockets. You might be able to force the screw in but you'll want to do this when it's not on the wall, upside-down and with a monitor/TV in the way! I ran an M4 form tap (not a normal cut tap) and brought the size up to M4 as I don't have any M3.5 screws that are short enough or have a large enough head.Once screwed in though, it's pretty solid and it's quite low-profile at just over 15mm. Don't forget that will increase if you need to use the supplied 16mm spacers or any sort of additional brackets.Another thing that's worth being aware of in the instructions is that it says to use a 15/16" drill bit for the supplied plugs. That's around 8mm but the plugs measure more like 10mm. I just used my own 10mm plugs.

Justo lo que necesitaba, buena calidad.

J'ai le plaisir de vous partager mon avis en vous les présentant sous plusieurs angles :1 – Quelle était ma recherche, mes attentes ?J'étais à la recherche d'un support pour un écran PC de 24 pouces, car je voulais absolument retirer le pied qui était fourni avec l'écran, celui-ci prenait beaucoup trop de place sur le bureau.2 - Pour quelles raisons, j'ai acheté cet article ?Ce support correspondait parfaitement à ma recherche pour les raisons suivantes :1 - Il était équipé de plusieurs VESA 50-75-100, ce qui est plutôt bien, si on change un jour d'écran2 - il est presque collé au mur, il y a exactement 4 cm, entre l'arrière de mon écran et le mur.3 - il est prévu pour des écrans de 17 à 27 pouces3 – Utilisation, installationTrès facile à installer, seuls trois trous sont nécessaires pour le fixer au mur.Une fois la plaque fixée au mur et l'autre plaque fixée au dos de l'écran, grâce au système VESA, ne reste plus qu'à glisser l'écran à l'intérieur de la plaque qui est au mur.Pour retirer l'écran, il suffit juste de le soulever.Ce support écran est livré avec les chevilles et les vis.Ce support écran ne permet pas d'incliner l'écran, ni de l'orienter droite/gauche, ni de monter/descendre l'écran.Je n'avais absolument pas besoin de ces options. En effet, une fois que j'ai bien positionné mon écran, je n'ai plus besoin qu'il bouge, ni sur les côtés, ni en haut/bas.4 – Qualité du produitLes plaques en acier semblent être de bonnes qualités, épaisses.5 – LivraisonAucun problème, dans les délais.6 – Conclusions3 systèmes VESA en cas de changement d'écrans, prix très correct, qualitatif, chevilles et vis fournis, et gain de place énorme.

Oggetto fatto molto bene. In realtà come descritto NON è 10mm di spessore ma bensì 14mm. Non credo che per la maggior parte degli interessati questa differenza sia apprezzabile. Nel mio caso, essendo il monitor a scomparsa verticale ( su camper ) , l'ingombro complessivo è uno degli ingombri da tener d'occhio.

Très bien, fait le travail.

If you want to mount a screen to a wall at the correct viewing height, and want to have it as close to the wall as possible, this system is about as good as you are going to get, short of plates which require access to the back of the wall. It's essentially two plates, one of which screws onto the back of your VESA-compatible monitor or TV (which is every modern monitor or TV), and the other which screws to the wall. Once you've done that, you slide the monitor into place. It takes about five minutes in total, unless you're screwing into a hard-to-drill wall.This system is not adjustable. If, for some reason, you need to put your screen above or below eye-height angled up or down, or want to have it tilted to the left or the right, this is not the right system for you. You can probably put shims in on the plate on the wall, or washers into the plate on the monitor, to give you a certain level of adjustment, and if you really want an angle and to be close to the wall, you may have to do this, but you certainly won't be able to adjust it afterwards.This is a good solution if you want to be as close to the wall as possible and you have a free choice of where you mount the monitor. It's also a better solution if the surface you are mounting to is not especially strong, such as wooden panels, because the shorter gap equates to less torque, and therefore less strain.