SKILSAW SPT00B Rear Outfeed

This is stronger and stiffer than it looks. Once installed it pulls in and out smoothly. There is a knob to lock it in the fully extended, fully retracted or any position in between. One caveat is in the fully extended position the support bar couldn’t be adjusted high enough to be level with the table top. Will have to shim the mounting a little to bring it high enough. Only a 1/16” or so. Usable as is so 5 stars anyway.

Wish the saw already came with it because it’s a vital part! Fits and functions perfectly.

Installed on my SPT99-12 -- took about 20 minutes.The directions are a little confusing -- there are diagrams but can be a little tricky trying to figure out which direction the brackets that hold the feed tray are supposed to be facing.It comes with two identical brackets, with a hole drilled on each side that a plastic thumb screw/wing bolt feeds into to adjust and hold the tray in place -- it would make sense that this hold faces outwards on both brackets (and it's hard to tell by the diagram if this what you're supposed to do), but if you install it as such on the one that is on the interior (by the motor), the width between the two brackets is not wide enough to fit the tray rails through.Fitting the bolts for the brackets can be a bit awkward because there is not a whole lot of room to fit the allen wrench to make a full rotation, either because of components of the saw or the brackets themselves -- you kind of have to angle your allen wrench in there to tighten them -- possibly rounding off the bolts.In addition, and I don't know how or what can be done to correct for this, other than making the brackets longer, but the rails tend to move independently of each other and can bind and move unevenly.Other than these problems (easy enough to deal with, especially considering the price of the tray) the machining and build quality is satisfactory and it does what it needs to do, fairly simply.

This feed out is a must have if you’re cutting larger stock, although some think it is a hard install I found it actually very easy and intuitive, it was a easy fit to the saw, it is actually custom made for the STP 99-11 or 12, it is the same saw, the only difference in the number is the sawblade it comes with, Negative reviews are unjust, don’t let this discourage you if this is an option for yourSTP 99 Skil saw.

Very happy with it. It actually seems to be a little sturdier than I expected.

Bought this the same time I bought the Skil tablesaw . I've seen reviews about this being difficult to install , it's not hard at all . Just do not tighten any screws till it's all assembled and use a little lock tight on the screws . A round headed 5 millimeter Allen helps also .

The most positive thing about the attachment is the solid quality of the components - solid steel bars and thick metal on the outfeed support. I've used it several times now and I am very pleased overall. The only aggravating problems started with the instructions, just plain bad. Also, I had to cut down an allen wrench so that the shorter side would fit into the bar support brackets and get them aligned so the outfeed would slide in and out smoothly. The quality of the product should get 5 stars though.

I installed this on my SPT99-11 and it fits and works perfectly. You have to look at the directions very closely - the guide tube on the left side of the saw installs somewhat un-intuitively. For both guide tubes, you will access the attachment screws from the right side of the saw. So for the right guide tube, it is easy to access the screws. For the left guide tube, you are squeezing your hand between the guide tube and the saw motor. Also, on mine the rods were already in the guide tubes and one was in backwards. Once the guide tubes are correctly oriented, the rods are parallel to each other and square to the table and meet the holes in the outfeed support as expected.

Great add on, poor diagrams provided. Brackets install with threaded knob threads both facing the Left Side(fence) if you're attaching from the outfeed side of the saw while in operating mode. Definitely gonna want ball end Allen Keys.

It is lightly below table surface but it should it prevents material to come backwards with vibration. Doesn't look like much but 15 inches is noticeable good for parts 48/ inches .. anything large and longer will require a roller ;)

Easy to install, works great

Quality well made rear fence.Collapse the saw stand, so that the table is vertical.Locate the mounting points for the rod slides .(Left and right is now top and bottom.)Mount both the rod slides with the allen bolts to the top.Just barely snug the bolts up, a ball end allen key / wrench will make your life easier. 5mm from memory.Insert the rods and add the washers and fence, tighten the end bolts. The rods have 2 flats on each rod so you can use an adjustable wrench to hold the rods when you tighten the end allen bolt.Slide backwards and forwards, should self aline.Go back and tighten the bolts on the rod slides, install the lock knob on the bottom rod slide.Done!

Rock solid!