ABEST Airbrush Quick Disconnect Coupler Release Fitting Adapter Kit with 5 pcs 1/8" Female Connectors and 1 Male Adaptor 1/8 Male -1/8 Female Hose Connections for Air Compressor, Airbrush Hose

Good quality and fit in this Excellent adapter set. If you use an air brush, these adapters are a must-have. Definitely recommend.

Works exactly as advertised. I'm able to quickly swap between different airbush guns.

Great product that fits all of my airbrushes and even replaced one that came on my Gahleeri that didn't fit my quick release. Plenty in the order so spares are on hand if needed.

Just received today, 2 days later than amazon prime said. QD are a must have! Havnt tried to use yet but male end comnects to female QD. Not sure yet about fit on airbrush, I use iwata. All of the male fittings are of same size, not a variety pack like some might think.these will not screw on passche AB, But if you get the passche male QD fitting, it will comnect to this or any other QD. Basically the end that screws onto airbrush IS NOT a universal fit, each AB has its specific size you can buy. TheQD part that attchs to airhose IS A universal fit, any QD will snap into each other. . You may need a hose adapter depending on yourhose/air compressor. Update... So the male adapters do fit my iwata, no leaks. The QD body though does leak a little bit depending on if you bump or move around the connection. Not a huge deal but thought tou would like to know. This QD is a generic brand, I also have a passche QD body made by passche and it DOES NOT LEAK at all. I would suspect all od the generic QD fittings will leak somewhat, so purchase a brand name QD and use the correct male fitting that screws ro airbrush and wa la. Leak free and still pretty cheap to buy. Hope this makes sense to you and helps you out.

Perfect

On the first airbrush I installed one of these on, air leaked badly. The second, it didn't. The first turned out to be a mistake on my part. As with *any* hose fitting, whether it be plumbing, air or otherwise: Ensure the gasket inside the fitting is seated at the bottom (can be pushed in with a toothpick or similar if not), and MOST IMPORTANTLY - DONT CRUSH THE GASKET BY OVER-TIGHTENING.When you feel the fitting snug up against the gasket, stop turning. You can also put teflon tape (plumbers tape) on the threads. It wasn't needed in my case, but I did it anyway since I always do it for anything plumbing related. If you are using tools to tighten these down, you are absolutely doing it wrong.

Just getting my feet wet with airbrushing and had gotten a multi-brush starter kit. I didn't want to be unscrewing the hose every time I wanted to use a different airbrush so I knew fittings like this existed for regular air-compressors, so I was excited to see they made them for airbrushes.So far these have been working great with no leaks.. except 1.. which looks like its a mixture of the thin metal and my brute force.. DO NOT OVER TIGHTEN these things.. seriously just hand tight.. turn on the air and connect the brush to the hose to check for air leak.. if you can hear air slightly tighten the fitting.. If you do like I did and wrench on it like its a water hose.. you WILL crack the fitting and have a leak.Just figured I should leave a review as I was back to buy another set to make my hose have a quick connect to the pump ^_^

This package appears to two different items sold as one unit. The quick disconnect and one male connector come in one package and the other contains 4 male connectors. This is a good thing! Because the male connector that comes with the quick disconnect does NOT have a rubber "O" ring in it and it leaks horribly to the point where it is unusable. (see first picture). Just throw that one away it will never work for you. The Quick Connector worked just fine with enough Teflon Tape. (you may have to push down on on the release ring a few time to get it to seat and not leak when your airbrush is disconnected.The 4 male connectors that come in the separate little plastic bag all have "O" rings inside (see second picture) and work just fine but you have to use about 7-8 layers of Teflon Tape on the threads because there is some play in the threads but they work. So you do NOT get 5 working male connectors you get 4 and you will need Teflon Tape to use this product. I hope I just got a bad one but if your having trouble with leaks add more Teflon Tape and Make sure there is a little black rubber "O" ring in Male Connector (the part that attaches to your airbrush).