Gifts for Men,Damaged Screw Extractor Set-Christmas Stocking Stuffers for Men Adults Him,Mens Gifts for Dad,Husband,Stripped Screws Nuts & Bolts Drill Bit Tools for Easy Removal of Rusty Broken Screw

This is a really nice set. I've had to use this several times to remove stripped screws. It has worked great!

I rarely write reviews, but these screw extractors were such a lifesaver that I felt compelled to share my experience. If you’re struggling with stripped screws, stop wasting time with DIY tricks and order these immediately.I recently faced a huge challenge while preparing to move: my expensive West Elm tables (worth over $1,500!) were held together by screws that were completely stripped. I tried every hack I could find online—rubber bands, liquid gripper, you name it—and nothing worked. I was about to give up and leave the tables behind when I stumbled across these extractors on Amazon.Not only did they arrive the very next day (thanks to Prime!), but they also worked flawlessly. The process is simple but critical:1. Use the drill side to bore into the stripped screw.2. Flip the bit to the extractor side to pull the screw out.Following these steps, I was able to remove the screws effortlessly. These extractors are an essential addition to my tool kit now, and I’ll never be caught without them again.For around $10, these tools saved me hundreds of dollars and a ton of frustration. The quality is outstanding, and they’re compact enough to store easily. If you’ve got stripped screws to deal with, don’t hesitate—these screw extractors are worth every penny.

Success on and old faucet screw with a disintegrated head. Can’t say much about the drill side, recommend an old fashioned bit of the same diameter. But the extractor worked well. Recommended.

I almost gave up when using the smallest one and it didn't drill deep at all( just like the other tool I bought earlier). Neither the extractor worked. I really don't want to mess up with the engine body. Then I give the second bit last try and when drilling I immediately felt the difference, it went deep and then used the extractor, the moment when the extractor head locked the bolt I knew it's working and the bolts just came out like a charm.

Worked really well for my set of stripped screws. Works almost instantly. Very easy to use as well.

I have an old Toyota Tacoma that I have been working on. I was removing one of the fenders when a small mounting screw head snapped off, leaving the remainder of the screw in the frame. I soaked the remaining bit of the screw and the hole with PB Blaster for a week, hitting it with spray at least once and sometimes twice a day.I felt like today was as good a day as any to try to get the screw out. I again soaked the remaining bits with PB Blaster, wiped away the excess, and attempted to sink the drill side of the #1 extractor bit into the screw. It spun, but had no impact. Not wanting to potentially snap off the bit, because I know how fragile they are, I switched to a left handed drill bit that was the same size as the #1 bit in the kit. After the hole was started and I saw that I was going in straight, I switched back to the drill side of the extractor bit and got it to sink into the hole, down to the stop on the bit collar. I flipped the bit over and attempted to extract.Using a drill on a slow speed, making sure not to put too much force behind it, I saw that the bit wasn't extracting, instead it was grinding away the metal stem of the screw. I applied slightly more pressure and saw that it was just grinding away more of the stem. I stopped with the #1 and switched to the #2 bit. This time to make sure that I wasn't going too fast, I used a 1/4 inch collar/guide on the bit and fit the other end of the guide onto an Allen wrench. Applying minimal pressure and turning about a quarter turn at a time, I finally got the #2 bit to bite. The bit was down inside the screw and decent amount. Since the #1 hadn't extracted and instead ground away some screw material, the #2 was seated really well in the screw body.Now with extractor seated and biting, hardly applying pressure, I pressed the allen wrench slightly to the left, and that's all she wrote.Now the extractor bit is buried in the screw, making the job infinitely harder since you can't drill through it.I read that a grinding bit in a dremel should be able to grind the extractor bit down and hopefully cause it to crumble. I just destroyed one grinder bit trying to get through it.Now I am looking at buying another "rescue bit" to remove the extractor bit that is broken off in the screw. I should have just left hand drilled the screw out as best I could. This thing is more of a headache than it's worth.

Not much to say — it works. Handy little kit for stripped or rusty screws. Quality is decent, sharp enough for most jobs, and the bits feel durable enough for light to moderate use. Not pro-level, but for the price and occasional need, it’s totally worth it. Good to have around just in case

Works half the time.