Dupli-Color (BFM0328-6 PK) Cayman Green Metallic Ford Exact-Match Automotive Paint - 8 oz. Aerosol, (Case of 6)

I use this to touch up sun damaged spots on my car. It held on for a while, but later on faded out as expected though if you want it to last longer, maybe topping it with a clear coat would work best.

I bought this to match the paint on a 2003 Dodge Neon. The paint was identical to the original. No issue with application. It has been holding up find for several months now.

It’s a perfect match but it’s half the size of regular paint cans and doesn’t not cover a lot still the match is important and 100$of dollars cheaper to do it your self

This was easy to use, and left an even spray. The color perfectly matched my Ford Expedition.

One can worked perfect for an entire fender for a 2006 corolla. When doing the next fender 2nd can had a split on the applicator tip spewing large globs of paint all over the place. I managed to finish the job by removing the tip of one can and replacing the broken one but the damage was done, now the repainted fender has large globs all over it which I hope I can sand out, butt Amazon stepped up and offered a refund so 5 stars for the first can and for Amazon service.

Brain dead application process and incredible results. I used this to paint some model cars and a game cube controller. The finish is amazing and the color has a ton of depth and well distributed sparkle. The paint dries quite quickly allowing me to get in several coats of paint in a relatively short period of time and get a very high quality finish. I also finished my projects off with the 2k clear coat which was just as excellent.

Used to cover paint on hood of car to protect. Not an expert painter and was doing an artsy project since the car is old and starting to rust. Did the full gambit of painting, sanded hood, primed, sanded again, then painted with Dupli-Color and with other paint for design then clear coated...so here is why I gave this clear coat only 4 stars.1. It is a nice clear coat but the can is small, wish it came in a regular size can so you have better pressure and so you can do more (I do realize it is made for touch ups).2. The hood was attached to car and was going to stay that way for my project, hence to do the top of the hood I had to spray almost parallel to the hood and could not "angle" can very much. This required careful planning after I realized that when you get about halfway through the can, it will not spray nicely (at all) if not angled. The can would work great if you could spray perpendicular to the ground to the piece you are spraying. So that being said, had to spray all the flatter areas first with the full can and then progress to the parts where the can could be angled to finish the hood.3. Read a lot about the humidity and about the hazing that can occur and it did happen. The humidity was only 2pts below the recommended humidity level but it doesn't get much better in the south...so you just have to go for it. Had better results with Sun overhead and humidity only 2pts below recommended level (not much hazing at all, if any) than late afternoon and much lower humidity 6pts lower (this is when I had the worst hazing that is now visible). When it did haze, I waited the recommended 10 minutes between coats and sprayed the hazy parts again, this made it go away...also did not spray as far away as they recommended on the can. Some of the hazing that I had also went away when it was allowed to cure for the 5 days but did have a "streak" left over from the haze that I did not go over (ran out of clear coat). Since I am wet sanding and polishing I am not too worried about it...wish I took a pic to show haze line but forgot to take pictures. Honestly, if I ever did this again I would probably look into how much it would cost to have someone clear coat it for me.4. Wet-sanding now and it is looking good (not near professional) but what I expected so far.I am not done with project but about 75% done and am happy with the results so far.

Excellent touch-up! It covered many pebble pock marks on my front bumper. Good price, too!

good product, took more than 3 coatings to cover the filler, though.

Best oneComments were spot on

It was used for being the correct colour match for a car manufacturers paint.