KitchenArt Baker’s Pro Adjust-A-Measure Set, 4-Piece, Satin

The measuring cups are absolutely the best item I’ve used in years. Just pour what you need in the cup and it’s finished!!! Then with a wipe of a sponge or kitchen towel it’s clean!!! What more could you ask for……..YES THEY COME IN TWO SIZES too!!!

This is such a good tool for difficult measures like mayo or nut butters. Good invention! All the measurements are on there, so good metric teaching tool for an old dog. :)

update: i finally found the 'trump card' for this exact tool. I have NEVER been able to get just the right amount of waffle mix into a waffle iron. My new waffle iron calls for 1 '1/3 cups of mix so i decided to try this tool out for the job. It worked without flaw, i can't imagine a better way to pull off that chore; my older 'wonder cup' style was so hard to push compared to this it would be a struggle to actually empty. The batter was just the right texture that it didn't stick to the top of the plunger i didn't even have to scrape it off just push the plunger and go.add'l update; my first copy had a bad seal so amazon swapped it no-charge-for-shipping etc. sadly that won't get the feedback to the source very well but at least the second one will 'hold water' which the first didn't. It doesn't hold water great though.. a tiny bit will leak through the seal but i didn't buy it for water, apparently i bought it for making waffles! If i don't use it for anything else it will be worth it for me. (i love waffles)=====1) mine came with some labeling smeared as others have commented on; this is definitely a quality control issue; the label ink seems pretty solid, it's as if it was boxed up before the ink was dry.2) there is a flaw in the desgn that allows the wobble. there should be a set of 'ribs' on the plunger to keep it centered in the outer tube. a very simple fix: wrap an o-ring around the inner plunger so that there is a second place to hold the plunger centered. make sure it's not too tight. even better; put an array of tiny rubber stick-on feet around the inner-tube (i did 3-around about every inch) it makes the center piston stay perfecly centered with the added bonus that it also holds any position very well. basically it's a design correction to fix the biggest flaw. if i can figure out how to add a picture later i will. again, quality control issue. the design of the seal is fine, but mine has a flat spot from a mold release or somethihng where water will just dribble right on through.3) mine came with a faulty seal; it literally 'won't hold water'. since i have much better tools for measuring water-like liquids i think i'll be ok with that since the primary use i have for this tool is measuring brown sugar, i'm not sure if i'll be sending it back.4) dishwasher safe may not mean dishwasher friendly. i'm not sure there is any gain in running the plunger through the machine, but the exterier tube is a solid tube of polycarbonate or similar very strong plastic. as long as it doesn't rub violently around in the mashing to rub off the lettering it should be fine for a long time. I don't expect i'll be needing to run mine through the dw.5) precision. i did a simple test of measuring 1c of water and it was within 1 tsp accurate. that amount of error is definitely withing the error bars of me eyballing the meniscus of the water. i'm satisfied with that result.6) pouring ability. agreed it should have a spout! what up with that? you can pour fine if the receptical it's going into is big enough to commit to 100% pour but often you'd want to slowly pour it in; forget about that plan.7) star rating. i'd give it 3.5 because of the quality control issues that are apparent but i'm rounding up because the overall design is superior to the lower quality soft-plastic models like schmamered schmef design. I've used that one for years, it 'gets the job done' but this one is an infinite improvement in 'touch and feel'. the other design has a closed plunger for measuring liquids not relying on the seal but it's nearly impossible to read through the thick opaqe plastic.8) read the directions: people are pulling the seal off by pulling straight not twisting as it says in very clear lettering on the top of the disc. the static coefficient of friction of a rubber ring on polycarbonate under pressure is 'off scale' it *should* rip off the disc. it would be better if they made this more clear but they are serious do not pull w/o twisting.8a) you could surely re-glue should you pull it off; that part is well out of the way of touching your food so it won't be needed to use a 'food safe adhesive'.9) storage suggestion; you can avoid that problem by following one of these ideas: a) NEVER store completely closed; just like a syringe will pull the rubber boot right off if stored fully depressed, you can expect problems if the first motion is to PULL out the pluger. If you leave even a cm of space or make sure to PUSH the plunger out you will never put the 'tension' type of force on the part so you can't break it that way. b) as mentioned in 'a'; PUSH the plunger the first time you use it after storage even just for minutes; the seal will 'stick' to the outside wall. if stored 'open a little' you can push it closed first then pull & twist open or if stored fully closed, push on the black seal to get things moving. and c) to help keep the seal from wearing out prematurely *and* help avoid self-destruction, put the plunger in backwards or store separately (even better). They made a slight bevel on the BOTTOM of the tube and when the plunger is put in backwards, there is about 10% of the force on the seal. it greatly reduces the problems assosated with the seal being tight.I'm going to contact the company about the manufacturing defects on my copy and i will post a follow-up to see what they suggest in regard to my faulty model and i'll adjust my star score accordingly.-awr

Great to have in the kitchen as a basic set and to compliment your other measuring tools. Be aware that the metal can do a weird splotchy discoloration thing in the dishwasher that doesn't seem to have any affect on the tool itself.

Bought this to replace the ones I had, dishwasher finally washed the markings off. Time will tell how it holds up.

Very useful that it shows all the different measurements. I wish it was a bit more sturdy. When adding in some ingredients that you need to put in it can slide down a bit.

Love the fact it has a dry side and wet side for measuring.

Used this for measuring syrup to be added in candy reciepes.

fantastic for measuring butter and peanut butter. No more trying to scrape out the contents. Great for all measuring. And love how easy it is to clean.

Had this now for over a year. Goes in the dishwasher and was invaluable for all the Christmas baking. Would absolutely recommend and buy another in a minute if something happens to the one I own. Always losing the measuring spoons and can never find the right size in our massive kitchen utensil drawer. Love this thing!

The media could not be loaded.  El material es muy resistente y es muy fácil de usar, solo deslizas para ajustar la medida (de 1/2 tea spoon a 1 table spoon) prácticamente son 6 cucharas en 1. En cuanto a la limpieza también es muy fácil, la tapita es quita y pon.

La calidad del producto es buena, es funcional y cumple con lo que dice, peeero al momento de ajustarla me gustaria que tuviera mas soporte o firmeza porque facilmente se mueve de la medida, se desliza un poco facil.Fuera de eso me gustó

a neat natty measure that holds all I need to measure.Its plastic so it cleans easily, but if it gets dropped, it might crack