Inner Bed Tie Down Anchors Retractable Truck Bed D Ring Compatible with 2007+ Silverado & Sierra 1500 2500 3500/2015+ Colorado & Canyon - 3000LBS Capacity Only Fit SideWall of 4

The media could not be loaded. This is a really highly engineered and solid all metal product. It does what it should without inconvenience or rattling. My way of installing in a Silverado is a breeze—back the screw way out but don’t remove it, extend the ring all the way, holding the ring slip the upper edge of the backing plate behind the bed wall, LIFT vertically the bottom edge of the plate can clear the wall and slip in, center it up, screw or down. It might take 5 minutes on the first one or two to work out the fiddliness (and to learn to be Gentle so the ring doesn’t snap closed), but after that it is about a 2 minute job.The one in the video has been subject to about 17 loads of compost, wood chips, and dirt. As you can see it wasn’t bothered by the grit and still works like a charm.

Took a couple minutes to figure out how to install them as the instructions are not clear (use YouTube). But once I figured it out they were easy to install. I have used them a handful of times and they work great.

These were so easy y to install. I had 9 in in less than 1/2 hour. I also like that they retract out of the way. And look good. My brother-in-law is jealous. LOL

These are OK. I have had 2 trucks of the same generation and used the other brand on the last truck. These are nice being mostly metal. They are easy to install and seem sturdy. This brand didn't seem to sit as straight as the other and do not seem to retract as flush. They stick out a decent amount even when all the way in. I attached a pic and it really isn't bad just something to note. They do seem very functional and I have no qualms about using them to tie stuff down.

2024 silverado 2500hd with line-x spray in bed liner.Super easy install, 20 minute total install time (even though I installed one upside down initially and had to take it out and reinstall). Lock the anchor into the open position, remove the screw completely, slide the main body into the pocket, then slide the backing plate into the pocket, holding the anchor in the open position slide plastic face against the sheet metal and reinstall the screw. Prior to tightening the screw completely, test the anchor for functionality. If it is operating correctly, tighten the screw and you are done! That's it!They seem to function smooth. They do NOT sit as flush as the "BULL RING" anchors, but the bull rings have more plastic components that breaks down over time.I have not put these under load yet, but they feel like good quality. These anchor points will be used as secondary security for my load, I don't trust the sheet metal to hold any excessive amount of load.5 stars! Very satisfied at this point!

Great. Not as easy to install as you would think, but as soon as you figure it out it all goes easily. I put a bunch of them in, filled every hole in the bed of my truck. Looks and works great

These tie down anchors look good and seem to be well built. I just installed them yesterday, so I don't have any experience in there ability to perform under load or stay put with the vibrations of traveling down the road. I will come back and alter the review in a few weeks if I find they don't actually function as expected.They are not exactly a breeze to install and people with large fingers will have some difficulty in holding them in position while trying to get the set screw started back in the threads. I resisted the temptation to grab them with pliers but you could probably just use a tie down strap hook to grab the loop and temporarily hold the anchor in place and get your fingers out of the way. It may take a bit of fiddling to get the retractable tie loop to move in and out, as the backstop plate can bind up with the loop. In that event, loosen the set screw and kind of slide the body or the backing plate up or down. Make sure the retractable movement is there before final tightening of the set screw. They are indeed all metal and look nice once installed.

Wouldn’t lock in

Super easy install. Nice slick tie-downs. Ready to go at all time but never in the way. I ended up put one in all 10 spots in the bed of my colorado. Makes strapping anything down in my truck a breeze

The media could not be loaded. I have purchased and installed this retractable tie down anchors by Tigeracing in my GMC 2500 HD truck for extra tie down options in 9 locations to prevent tools sliding around and stay secure in place. My truck had already drilled out the holes and this anchors fit perfectly without modifications.The installation was not difficult and straight forward with easy to follow instructions, a #2 Philips screw driver is needed for removing and re installing the single screw in each anchor. See my installation video for details and hope it helps.The anchors themselves, are build really well, CNC precision machined to size aluminum blocks, and stainless steel loops and hardware with spring loaded for easy retract when not in use and also locks in extended position to easily hook on the straps. The backing plate is fairly tick (2mm), I would say they are heavy duty, listed at 3000lbs capacity, I think this is combined load capacity between all 9 anchors if used together, it makes sense at about 330 lbs each but I can see them holding a lot more load. As calculated from ANSI 304 tensile strength for this nuts and threaded loop (as a bolt)each can carry loads up to 3400lbs x2, that’s impressive and leaves to look at the weakest point, the backing plate of the anchor at 2mm thick and the truck sheet metal gauge that could bend under high tension but for my use they are perfect. Very good value for 9 pc pack at just $16/pc, they look really good and functional. Thanks

The Amazon garage filter was saying that they do not fit GMC canyon 2022, but they do, I love the fact they are retractable so they are not in the way went not in use

muy buen producto ampliamente recomendable

Easy to install and very practical.