Woodstock W1005 14-Inch Table Saw Flange

This fit perfectly on an old Craftsman 10" table saw. I needed to drill holes to attach to accommodate existing 1/4" machine screws in saw base. First two holes went without a hitch. The second two cracked the plastic. Used a rotary tool to finish the holes. Yes, I had clamped down to prevent vibration. I ended up using epoxy to repair and reinforce the holes. Other than that was happy with purchase.

The Woodstock W1005 dust Collection Flange is what it clams to be a plastic flange with a 4" dust port in the center. The reason for 4 stars is the price is just a bit steep for an item that I would think costs only a fraction of the retail price to produce, but that being said, so what, you are going to get gouged on anything tool related these days.The quality is good, after all it is only a molded hunk of flat plastic with a hose port in the center there is not much that could be messed up, and there isn't anything messed up.I installed this item beneath an old previously very rusty Sears Table Saw that I am doing the resurrection thing kind of like in a Frankenstein horror movie. After being disassembled and the rust removed and a little body work to the banged up sheet metal and a new arbor and a new set of trunnion bearings I gave it a couple of coats of paint now the thing looks great and runs as smooth as silk.These old saws were not made with dust collection in mind so the bottom is totally open as is the rear panel as the belt drive from the external motor comes in the back of the chassis, a horror for dust collection. As it was you could cough up a lung after being in the shop with it running and tossing sawdust everywhere possible, so some dust collection modifications were mandatory.This flange was just a tad smaller than the base of my saw so I had to build an adapter flange out of a sheet of 1/4" plywood to totally fill the bottom, not a big deal but took some time to make it be nice like the reworked saw that sits on it.A long way to say it does the job it is intended for it is way better than just letting the sawdust go on the shop floor. Not an ideal installation in my case but it works just fine.Happy with this product, would buy again.

Good product. Good quality. Good price.

Needed better dust removal for my table saw. After adapting it to the saw and blocking other air leaks it is working well. I have it connected to a dedicated shop vac with reducer connector. Happy with product so far.

This does what it was designed to do and that is catch the dust that falls directly down from the blade. this does not magically capture dust on the table top or dust that comes out of the back of the saw. the reason i gave it three stars was due to the fact that i had to seal some minor gaps along the ridge of the table saw where this shroud did not cover and i had to make a "gasket" out of thin plywood on the under side of the saw because the shroud wouldn't quite fit inside the saw due to the trunnions getting in the way. when all is said and done this is really the main part of the dust collection beneath the saw and it works as well as it can. i have it necked down to a 2-1/2 in hose and it catches the larger particles well.

It’s a piece of flat pvc. Nothing special. Works great for what I’m using it for.

I built a custom table saw with router table extension and with the way I had designed the rollable table, I needed the clearance of the dust vent at the bottom that the included dust collection vent did not provide. This worked perfectly for the task.There is no problems with the quality of this flange. If you run into clearance issues as I have, this maybe worth looking into.

It's a plate with a 4 inch hole in it. not much to report. I installed in the bottom of my contractor saw as I was to lazy to make one. It probably saved me 10 minutes of work so not work much that way.Three stars as the thing should be more of a funnel. I have a 1 HP delta dust collector hooked up just to this on 6 foot tube. Not enough to pull sawdust from more than 2 inches away from center hole.

This seems really sturdy but I had to return it because it didn't fit my saw table.