Specification: Dimension: 20mm x 25m (Width x Length) Glass fiber thickness: 0.15mm Thermal Conductivity:1.5 W m k Breakdown Voltage: 5KVAC Thermal impedance : 0.3 x2103;in2 w Initial Adhesion: 1.5kg inch 180°Adhesion power: gt;18 N 25mm Applicable temperature range: 30~+150 °C Features: Thermal conductivity and high stability, its life than the general heat double sided stickers long, normal temperature (30~+150 °C ) can work for a minimum of 5 years. Notes For Attention: 1.When using thermal conductive double sided tape, keep the adhesive surface clean and dry. 2.After tearing off the heat conductive double sided tape to peel the paper, double sided thermal tape is evenly pressed with your fingers (just a little strength). 3.The viscosity of the heat conductive double sided adhesive tape have initial viscosity and persistent viscosity, and at room temperature, it takes 72 hours to achieve the maximum adhesive strength, That is, at the beginning of the sticky adhesive that is the initial viscosity to 40% of its maximum viscosity, persistent stickiness is stable over time. 4.In the paste process, the appropriate heating (60 ~ 70 x2103;), will greatly contribute to the effective increase in the area of adhesive, and as soon as possible to achieve maximum adhesion, In the lower temperature of the winter, it 39;s little tips that heating to increase the viscosity of the heat conductive double sided tape when using the thermal conductive tape. Package included: 1 Roll Thermal Conductive Double sided Tape Review: Replaced manufacturer ESC-heatsink thermal tape, and is still doing a good job at transferring the heat. Very sticky once set; fairly thick, can be cut easily, quality is good. Note that it's fairly difficult to remove residue if you remove it after it has set. Review: So, I cut a chunk this size> 1-3/16" x 3/4" I have a TUF GAMING Z790-PLUS WIFI D4 mother board factory heatsink they are flat aluminum very thin double sided thermal tape # (x002TZHUPX 1"x66') very thin. I put it on the bottom of the chunk I cut out. the first pic is show you where the controller is on that brand name SSD on the flat part of the factory heatsink over the controller is where you want to pull more heat out of the SSD. It still run warm it takes longer to heat up now it runs 36C at idle, and at heavy gaming it hit 40C. I drop 2C with the New Peerless Assassin 120 SE COOLER 3 fans over the Hyper 212 BLACK 2 fans before the extra Heatsink for the Controller. On a i7 12700KF 12GEN 10 fans air cooled only. (room temp 25.4C / 77F) It been on three days, two days 2hr each day game play. So far pretty happy but may have to get an aio to help cool a bit more. I hope this help some others.
| ASIN | B0751GYD6N |
| Are batteries included? | No |
| Best Sellers Rank | #203,541 in Industrial & Scientific ( See Top 100 in Industrial & Scientific ) #125 in High Temperature Tape |
| Brand | AVNTKER |
| Customer Reviews | 4.5 4.5 out of 5 stars (224) |
| Date First Available | 6 March 2018 |
| Item Weight | 168 g |
| Item model number | ANT-0052 |
| Model number | ANT-0052 |
| Package Dimensions | 11.71 x 11.61 x 2.9 cm; 168 g |
A**X
Replaced manufacturer ESC-heatsink thermal tape, and is still doing a good job at transferring the heat. Very sticky once set; fairly thick, can be cut easily, quality is good. Note that it's fairly difficult to remove residue if you remove it after it has set.
P**6
So, I cut a chunk this size> 1-3/16" x 3/4" I have a TUF GAMING Z790-PLUS WIFI D4 mother board factory heatsink they are flat aluminum very thin double sided thermal tape # (x002TZHUPX 1"x66') very thin. I put it on the bottom of the chunk I cut out. the first pic is show you where the controller is on that brand name SSD on the flat part of the factory heatsink over the controller is where you want to pull more heat out of the SSD. It still run warm it takes longer to heat up now it runs 36C at idle, and at heavy gaming it hit 40C. I drop 2C with the New Peerless Assassin 120 SE COOLER 3 fans over the Hyper 212 BLACK 2 fans before the extra Heatsink for the Controller. On a i7 12700KF 12GEN 10 fans air cooled only. (room temp 25.4C / 77F) It been on three days, two days 2hr each day game play. So far pretty happy but may have to get an aio to help cool a bit more. I hope this help some others.
C**7
This stuff takes a bit to get used to but once you get used to it it is simply amazing. I will most definitely be buying more for future projects.
D**N
Used to put a heat sink on a Starlink router. Worked great. Has strong hold and cut nicely.
B**G
I picked up a roll of this tape, not for its usual use. Oh, I will be using it for future computer builds, but I needed it for an unusual use. I'm a ham radio operator and retired EMT. As a ham I do a lot of public service activities and I volunteer as a weather spotter for the National Weather Service. I drive a well-equipped Jeep with several radios, emergency gear, supplies, and equipped with emergency lights and strobes. One problem I've had is that I can't attach anything permanently inside the cabin, so my microphone mounts and switch mounts have all been of the 3M adhesive type... except it kept failing due to the extreme heat we've been having here in the south and southwest. In particular, the switch to control my strobes simply would not stick for more than a day or two, and the mic holders were falling off every night. I'd pick the mic and holder up off the floor when I went out in the morning, scrape off the 3M foam automotive grade tape from the older and put a new square on and it would fall off again several times during the day, even with the A/C on. Then I thought of using this stuff... BAM! No more mic holders falling off! No more switches dangling under the steering column! The switch and two mic holders have stayed attached all summer so far without even once falling off or dangling! We've had some days well over 100℉ with temps inside the Jeep hitting close to double that and it's all still secure. This tape is great!
Trustpilot
1 week ago
3 days ago
