Leapers UTG PRO Made in USA Ruger 10/22 Picatinny Rail Mount , Black

I purchased a different rail earlier (won't name the company as I don't want to put them on blast) as it was stainless steel in color so it would match my Ruger 10/22 I-Tac barrel. Unfortunatley, the screws that came with it were too long, so the rail would not clamp down on the rifle nice and tight allowing it to wobble around even though it was specifically listed for a Ruger 10/22 rifle. This rail is perfect, nice and tight fit. My buddy has the same rifle and I sent him a link to this product and he ordered it as well. Very inexpensive and it does the job, can't go wrong.

I have a takedown 10/22 that I have equipped with a Williams peep rear sight fitted in the factory dovetail in the barrel. I have tried several scope bases on the receiver from factory to Powers Custom and a couple others big name brand bases and they all partially block the peep sight aperture when the optic is removed. This USA made UTG Pro has a radius groove cut down the center so it in no way blocks the rear peep’s aperture. I don’t know if it would block the sight if using the factory fold down sight so I can’t address that. It was easy to install, has T marks, if that matters, and comes with an extra mounting screw to cover droppage. My only complaint is they did not give you a torque setting for tightening the screws. However, 10 INCH pounds seems perfect and is what another brand of base recommends. The machining is perfect as is the matte black finish. Scope rings mount up perfectly and fit and placement of screw holes is perfect. While you big name brand fanboys who do more showing off and proclaiming how much you spent on your firearm will not be impressed, if you actually use the device you’ll have no complaints at all.

I couldn’t ask for better fit and finish. The only thing I found a little odd these days is that the screws were the “flat head” (slotted) type rather than Torx or hex drive that are a little easier to use and are more common with gun sight mounts and bases. As mentioned elsewhere, a recommended torque setting would also be useful even though I found 10 in-lb with an Internet search. Best of all: Made in the USA!

The rail fits exactly as advertised and looks great. My only complaint is the plastic and cardboard packaging allowed for most of the tiny screws to fall out prior to opening.

For the price you’d think it would be just good enough to get the job done but after installing and using it along with many other rails I found it’s very well made with excellent fit and finish. Make sure you torque down properly with recommended torque spec as you would with anything else and depending on your optic and ability you’ll have no problem getting 1/2 grouping at 50 yards in a matter of a few shots. Ended up getting a Kidd extended rail later on (another amazing review on that) but when my wife brought home a 10/22 that came with some junk rail I had to pass this on to her with confidence knowing its potential and she was stacking tacks in no time at all. Highly recommend.

Made in USA. Machining quality and finish excellent. Measurements are dead on, including mounting holes. Included are 5 screws because they somehow knew that I would drop one and never find it. The screws fit perfectly, and stop short of protruding into the receiver's interior by about .020". Now the one thing that would make this even better is if it were longer on the back end. There is over an inch of extra space on the rear of the receiver where this could have been made longer. I mounted my scope as far back in the rings as possible, and mounted the rings on the rear-most slots, and still have to move my head forward on the comb. If they make one that's longer, I'll buy it.

Works great on my Ruger 10/22 with scope rings that are picatinny.

This a really well made, quality scope base for the Ruger 10/22. I am 100%satisfied.

As advertised. Made in USA. Good quality. Good coating. Easy install.

Passt perfekt und macht einen hochwertigen Eindruck.

Parfait

exactamente lo que buscaba

I ordered this to replace the mounting rail that came with my rifle. The one that ships with the ruger 10/22 only has shallow notches which wouldn’t allow my sight to seat properly. I fitted this picatinny rail which is an easy process, the pre drilled holes line up with the threaded holes on the rifle and the screws provided fitted perfectly, holding everything securely in place. The quality of the part feels and looks good. I’ve attached a red dot sight to this picatinny rail and used it at the weekend in a practical mini rifle competition and it performed perfectly.