YATO Tiles Cutter 125MM 1400W Wet&Dry

Excellent cutter. Used it to cut at maximum depth. No problems. Was able to cut very accurately with guide. Certainly powerful enough. In my particular case a different cutter disk to the one supplied worked best.

Saw arrived well packaged and in good order. Feels solid and well put together. Only minor issue I had was setting up the water spray nozzle. This was a different design from the instruction sheet, but with a bit of fiddling around got it lined up and working. The attachment to the water supply hose was also a bit of a pain as its just a push fit onto a garden hose and tended to "blow off" when water was turned on. This was overcome by inserting a small piece of pvc pipe inside the garden hose, pushing the fitting on and then securing with a cable tie. Make sure the water flow is adequate, if not you will get a build up of material inside the blade guard. The saw itself cuts well and does what it's supposed to. The foot plate of the saw only covers up to the blade, which means any straight edgge guide jig or bracket can only be used on one side, there is also very little clearance between the saw motor and the foot plate, which means you have to use a thin material for your straight edge guide. On the whole is it worth the money? Yes, I'm very happy with the results I got and was able to get a near factory finish on the edges of some engineered Indian sandstone slabs, achieving a < 0.25mm accurate cut over 900mm slab length. Just take the time to set up the saw, check the blade for square and do a few practice cuts. I haven't commented on the diamond blade supplied as I never used it. I purchased some Anesty blades from Amazon, which have performed well for me in the past, for the fine cuts. All in all a decent saw, which performed well, once I got the water supply sorted out.

This is an unknown brand to me so I took a gamble. I was not disappointed. The powerful motor and new blade(supplied) cut through granite with ease. A few 'buts' The hose adapter did not fit on any of my tap connections, the water nozzle supplied did not match what was in the diagram(educated guess worked out where to fit it). The clear hose I will replace for a longer length. However, once set up no problems and task completed

We brought this to cut some quarts worktop safety! Brilliant machine. Should do our block pavement replacement bricks in future

It works but the water connection could be so much better and easier and something is not quite right about the guide plate.

With a diamond cutting disc, this tile cutter had no problem with straight cuts in 2cm thick outdoor porcelain tiles, it made a smooth cut edge, and after a quick sand with a diamond pad, difficult to tell from the factory cut. Taking it slow good result were obtained. I had some doubt given the price but would recommend for a DIYer. You need to give it a water supply, I attached the supplied adapter to a Hozelock type hose connector on the outside tap, it wasn't a tight fit but put some tape around the joint and it was fine. Overall this did the intended job perfectly and gave better results than I expected.

Saw cut through porcelain pavers 200mm thick, no issues connected to a pump sprayer worked brilliantly no dust when using a thin porcelain diamond blade, very little chipping

Excellent piece of kit for the money. Used it for cutting granite copings. Also bought a raking blade and then used it to cut drip strips

Am Anfang habe ich die Diamantscheibe mit der Beschriftung noch vorn eingebaut und ein paar Längsschnitte durch meine 90cm lange Platten gemacht. Dann ist mir aufgefallen das es nach der Richtungsvorgabe der Scheibe falsch herum ist. Also hab ich sie gedreht. Da läuft sie bei mir aber nicht so gut durch das Material. Schlecht ist auch wenn die Kühlung noch läuft und die scheibe zum Stillstand gekommen ist, dann verzieht sie sich und ist nicht mehr zu gebrauchen. Ich hab mir die billigsten Scheiben (3x für ca. 25€) gekauft, mit dem gleich Diamantprofil wie die Originale. Hab dann nochmal mit richtiger Drehrichtung eine neue Scheibe eingebaut. Und dann wieder "falsch" herum eingesetzt. Also ich hab definitiv bei meinen 3cm Platten wesentlich bessere Schnitte. Das Wasser wird so optimal mit in den Schnitt reingezogen und spült das Material weg.

muy buena maquina

Inarrestabile, fatte le scanalature in caldana per le nuove linee di riscaldamento. nessun cedimento. migliorabile solo il sistema per bagnare la lama, tende a sfilarsi dalla gomma dell'acqua.

Très bonne scie, belle coupe , qui nous a permis de finir les coupes du carrelage céramique de notre terrasse

Funziona molto bene, io la sto usando per un gres da 2 cm e taglia senza problemi e senza fatica, l'unica pecca ma è banale e il raccordo per collegare il tibicino alla gomma, magari servirebbe qualcosa di più serio..