75 T-Track Table Fence System for Woodworking Accessories, Miter Saw Fence with Laser Measure - Fits Portable Table Saws, Band Saws and Cabinet Saws (Fence Only)

I found this a bit fiddly to set up. The miter bar comes with delrin or similar plastic washers to adjust the fit to the slot and my saw has a stamped deck which seems to have a tight spot in the middle. It took an hour or so to get the bar running smoothly. I finally resorted to filing the last washer (under the protractor), but it works well now. Similarly, getting the protractor aligned was a test of an old man's patience.Once set up was finished, I tested the gauge by cutting segmented circles. It worked perfectly at 22.5°, 30° and 45°. It may be that the more expensive versions of this tool are better calibrated at the factory or easier to set up, but I can recommend this tool very highly for patient woodworkers.

After reading the comments and looking at the design. I took the bait and had to see for myself. This gauge is high quality and an absolute must have in the arsenal. Extremely accurate on every measurement I set and it locks in place with a tooth that is very accurate with no play in it at all. The bar is fully adjustable and takes work to get that perfect fit. Anything with a bar going into the slot on the table needs advanced adjustment first. Highly recommend this for the hobbyist. You won't regret it under proper setup and use.Pro Tip:MEASURE TWICE CUT ONCEALWAYS VERIFY ANGLES

The Good: Nicely anodized. Most parts are good quality. It comes with two of the hex wrench sizes you need.The Bad: You get bags full of parts but no instructions, though not hard to figure out if you have experience with this type of device. There are 3 larger, silver colored setscrews but nowhere I could find that they would be used. The item comes with two hex wrenches to adjust the fit in the miter slot, but no hex wrench for the screws that attach the miter gauge to the fence. The miter slot fit adjustment is a bad design. Even all the way loose, they're too tight in the slot. The T-slot washer at the tip of the bar fits too tight in my miter slot, so I removed it. Also had to remove the fit adjusters (there are four, one is hidden under the indexer). The final coup-de-grace was when I checked it for square with a machinist square and found that the miter gauge is not dead square to the slot bar when the indexing "pin" is in the 0 slot. Sorry I didn't take pictures, but I wanted to bag it right up and send it back. Some people might find this adequate for the price after removing the t-slot washer and the fit adjusters. I need something better, that works without a lot of fiddling, and is square. One star because it's not dead square when indexed to 0. A miter gauge needs to at least do that one thing right.

No directions, extra parts and don't know they go. Product is nice but confusing to put together.

Just tried out the miter gage. Looks like it will work well for me. However, the "rubber" cushions in the gage make it much too tight in the slot. Maybe they are for a larger slot but taking the cushions out was difficult. I used a knife, a tiny flat screw driver and a needle nose plyers. The most difficult one to remove was the one closest to the fence which I removed Once "rubber" cushions were removed the miter works very well.I found the miter gage to be square. I checked it both against the blade with a square and out of the slot. Both ways it was square for me. In addition, the package includes two set screws. Looking at the miter gage from the back there are two threaded holes for the set screws. If the miter gage is not square use the set screws to adjust the fence and make it square.I have seen minimalist instructions but this takes the cake, no instructions. Watch the advertisement video to see how to put it together. But I did it without the video.My complaint about this miter is having to take out those rubber cushions. I even jammed and scraped my finger in the process. They were hard to remove and there are no instructions on how to do so.I do recommend this miter. I think it will work well for me.

product works good

Why did you pick this product vs others?:Price was my number one concern. I liked the fence was set up for box joints. I was surprised how the product was packaged, wrapped up in some styrofoam. I Was truly expecting it to come in a box perfectly packaged, that was not the case. Upon examining it I saw scratches which made me think that this was used or I received some repackaged return. Furthermore it was missing the box jig and an Allen key.No instructions . I was going to return it but I put it together and tried it out. Everything was fine; square and tight fitting so I cancelled my return. I will avoid this company in the future.

A must-have for my Dewalt table saw. Makes the difference between amature and professional