TUXING PCP Air Compressor,4500Psi 30Mpa High Pressure Air Pump, Built-in DC12V/AC120V Power Converter,Auto-Stop,Oil&Water-Free,Paintball and Scuba Tank Compressor Pump(TXES062)

This compressor worked great once I figured out what I was doing wrong. I have a new umarex air saber, and this compressor would not put air in the tank no matter how long it ran, not the compressors fault though. It seems that with a brand new PCP rifle you must first "seat" the seals before it will take air. This is accomplished by using your shop compressor. Only take about 100 psi of air to seat them and then the pcp compressor can then fill it. The PCP compressor adds air in small amounts, and not at a sufficient pressure at first to seat the seals. While your shop compressor can't fill your rifle, it can give a blast of air that the pcp compressor does not. This is true of all pcp compressors. I do like that you no longer have to wire up the transformer to use this, as they have provide a transformer with lugs just like a battery has. you use the battery clamps, neg on neg, pos on pos, done. That is a nice improvement. Mine came with extra parts pressure test fitting, extra filters an extra pressure relief valve and extra o rings. . The filters are not that great I will probably get a better filter system. I have only had the compressor a couple months, so i can't speak to it's life span, but it aired my air saber up to 3600 psi from 0 psi in very short order. perhaps 10 min. You do have to stay with it as there is no auto shut off, and you need to watch the temp, that it doesn't get to hot. Heat will kill it. If it is a hot day, much better to air your rifle in 2 or 3 goes then it is to fry your compressor by being impatient. I leave the fan running after a fill for 10 min or so to cool it down quicker. Overall a great compact unit that you don't have to mess with water cooling mumbo jumbo and very straight forward operation. In my opinion worth the money! If you want it to last a long time, do not overheat it. That is true of any compressor. It is awesome that it will run off of your car battery too, just make sure the vehicle is idling so you don't drain the battery. They seem to have improved this product since some of the other reviews were left on here. No wiring now, better quality control ( mine worked great right out of the box), I will say instructions are lacking. Common sense will get you far though!

I use this compressor to fill a Hatsan Flashpup wood .22 PCP air rifle. It fills the 165cc reservoir from 100 bar to 200 bar in less than 2 minutes. The compressor came with the 12v 50A power supply and all the wires with terminals to connect it to the compressor. The power cord did not come with terminals and is a 2 wire no ground connection type. I used a 3 wire power cord from an old computer so I would have a good grounded power connection to the power supply. Also included are the 2 battery clamps with wires and terminals to connect the compressor to a car battery. The fill whip that is included is 23 1/2 inches long. It includes one small water/oil separator filter with extra filter media plus Foster quick disconnects at each end. I added a larger water/oil separator filter to make sure I am getting dry air. The compressor has no labeling on it but the manual explains each switch and knob and it is very easy to operate. The compressor is the same as the Hatsan Spark and is very compact and well built. The digital temperature gauge reads in Celsius and the temperature should not exceed 90c. The manometer reads in MPa so 20 on the gauge equals 200 bar, very simple. The compressor is completely air cooled using 2 internal fans. I have filled my air rifle about 20 times so far with it and it never gets close to the max temperature. I did a pressure leak test with the supplied test plug in the end of the fill whip before using it for the first time. The pressure release knob was leaking when finger tight. I tightened the knob very slowly with pliers till it stopped leaking. Now it works flawlessly when finger tight with no leaks. I am very happy with how well this compressor works and how easy it is to operate. This was a much better option than a hand pump or carbon fiber tank. I can use it at home or in the field and it is quick and easy to use plus the price was less than a 90ci carbon fiber tank. This compressor made it a lot easier to get started with my first PCP air rifle.

I used this for a few months for my PCP air rifle. It worked great for a few months. I kept a close eye on temps so as to not overheat it. Now as it builds pressure the pump just slows down and turns off at about 3k psi. May look like a good value but buyer beware.

First of all I want to let everyone know I am a trained Pneumatics Technician and not just some dude with an opinion. This review is a bit long winded but for a good reason. I purchased this unit like others to keep from having to fill my PCP from tanks and would love to give it a 5 star rating but just cannot. There are lots of other options out there but some of them are considerably more costly so one must shop price vs. value as I did. I would say for the price this unit is a 5 star buy. There is, however, one issue I must mention for completeness of this review. The unit itself is of high quality and works well...except for the supplied (cheap and low quality) hose. First thing I did to test the capabilities of this new unit was to pressurize the system with nothing connected except the supplied hose, starting at 1000 PSI and slowly working my way up to the maximum pressure rating of my PCP (3000 PSI). Thankfully the unit comes with everything you could need right out of the box (in-line filter, extra filter cartridges, and the hose plug needed for doing a unit pressure test). I would however recommend that you seal all threads in the hose assembly connections with thread tape as I did prior to first use (which is not done from the manufacturer and the tape is not included). The unit is loud (would be hard to talk over in close proximity) when in operation but the internal fan is very adequate and keeps the unit surprisingly cool, thus the noise is not something I am concerned with. Maximum temperature reading I have ever recorded was 112.5 degrees Fahrenheit (very cool at these high pressures). The supplied hose starts to leak excessively from the manufactured plastic to metal areas once pressure is around 2000 PSI. Don't get me wrong...the unit does exactly what it is intended to do...however due to the hose alone it does it very inefficiently. The hose causes the unit to bleed down from 3000 PSI to 2000 PSI while doing pressure check in a very short 6 seconds (way too quickly for my taste). The unit with the supplied hose filled my 500CC Seneca .357 Recluse from 1000 PSI to 3000 PSI in roughly 10 minutes. It probably is capable of half that time if it had a quality hose that did not leak. If you have an even higher pressure PCP then it most likely will take quite a bit longer. I even went so far as to report this as a defect and they sent me another (same low-quality) hose. I personally will be buying a separate hose of much better quality to remedy this issue. All in all I would recommend this unit to anyone who wants a reasonable cost and more convenient way to fill their PCP...just be prepared to buy a new hose...that is if you can't stand for inefficiency...what can I say...I have mechanical OCD.

This pump is very good quality, and I am sure it will work perfectly. CC I haven't really used it because of one thing; it has manual shut off. This is the second high pressure air pump that I purchased, as the first one had a couple of drawbacks, namely separate voltage converter and manual shut off. This time I was determined to buy one which had the voltage converter built in, and which had an automatic shut off. I don't know how I ended up with the one that has to be shut off manually, but that isn't going to work for me. I don't think that an air compressor should be built without an automatic shut off. I've owned a number of air compressors for running air guns and for running other air tools, inflating tires etc, but they all have shut off automatically when the pressure tank reaches its limit in addition to having a safety pressure release, in case the automatic shutoff should fail. If you buy this make sure you get the model with a serial number ending in -2 which has the automatic shut off unless you're sure that you want to watch it very carefully while you're using it, and be ready to replace the safety release part every time that you forget or stop paying attention for a minute

After much research, I finally bought this unit. I read every review I could and watch as many YouTube reviews as possible from numerous sellers. I was prepared to spend 30 minutes of so setting this up. It took me 30 minutes of reading the instructions (4 or 5 times) to make sure I was not missing something. Since there are no lose wired to connect to the converter, I was able to plug it in and was using it in ~5 minutes. I was almost disappointed given the 'complexity' expectations from other reviews by other sellers. Noise Level The cooling fan is as loud as a handheld blow dryer set on low. The compressor was significantly louder, BUT slightly less loud than a conventional air compressor. I will more than likely use ear protection because I am careful with my hearing, though I am not sure it is needed. Packing The unit was very well packaged and short of running over it with a tank it would be difficult to damage it in shipping. Documentation Adequate. There are a few sentences that will make you stop and retranslate due to grammar or sentence structure. These are not show-stoppers but brought a smile to my face. I remember attempting to learn a second language and realize that some phases are challenging to translate into a second language. Unit Appearance This product is well made, very well made. I found no rattles, lose screws, scratches or visible cheap materials. It is a solid product. I am impressed. Setup My unit is configured to plug a single adaptor plug from the converter to the unit. The connector looks like a fuse connector you see in the vehicle. No individual wires to attach. Simplicity is your friend. Compressor Temperature I refilled outside in 90-degree heat (32 C). The unit reached a maximum temperature of 108-degree (42 C) after ~ 5 minutes of use. Weight and Size This unit is mobile but does weight more than I expected. It weighs in at ~11 pounds (5 kg). The size description on the site is accurate (~12" L x 11" W x 8" H or ~.3m L X .3m W x .2m H). I was able to fit the compressor, the converter and all spare parts easily into a backpack for transportation and storage. Refill Speed I degassed my Umarex Gauntlet and then refilled. From zero to 3000 it took less than 5 minutes. This was with a High-Pressure PCP Hand Pump Air Filter Water-Oil Separator installed. Thoughts – So Far I have used it a few times with excellent results. I did not rate this products longevity since I have had it less than a week. I will be surprised it does not last several years or more. I recommend this product to anyone in the market for a PCP air compressor.

This little compressor has been used very heavily and just keeps going. I did open it up after about 6 months to tighten some nuts that worked loose. Both with a inverter and straight off the truck battery it works great. It is not quite but could be worse.

Fairly light and easy to transport. 110Vac or 12Vdc power options. Only tested 110Vac power supply hookup so far but that works flawlessly. No leaks, used right out of the box as-shipped. Fan is a little louder than I'd like but I don't need to set up a waterpump+bucket+hoses cooling system or fill+maintain+change oil like on the Yong-Heng compressor. I'll take the fan noise over liquid cooling setup and oiling maintenance every time! A little slower than I'd like but still MUCH BETTER than hand pumping. For now I'm only filling rifle tubes of 255cc or lower volume to 3000psi so it takes only minutes to fill. MANUAL shut-off so DON'T WALK AWAY while filling. Gauge scale on compressor is different than most of my air pressure equipment. I find the best accuracy using the gauge ON THE RIFLE to determined when max-fill-pressure is reached and then MANUALLY turning off the compressor. I don't find this an inconvenience in any way. Quite happy so far with this pump purchase. Rated 5* for performance/dollar :-)

Compré este compresor para la carga de depósitos de aire comprimido de hasta 200cc y a 230 bares de presión. El envío fue rápido y el producto llego bien embalado y con sus accesorios, los acabados son de calidad. NO HE TENIDO SUERTE CON ESTA UNIDAD ya que sólo lo use 8 veces y desde el principio hacía ruidos extraños, no funcionaba de forma uniforme y tardó mucho en llegar a 200 bares; nunca pasó de 43 grados de temperatura de trabajo. Ya no cargaba a mas de 40 bares y los ruidos metálicos y golpeteos internos eran muy fuertes, parecía que fuera a griparse o bloquearse. Me puse en contacto con el vendedor y facilitó instrucciones para desmontaje, comprobación, limpieza y ajuste. Desmonté y volví a montar 3 veces pero sin resultado, ha quedado prácticamente bloqueado mecánicamente y no carga. Envié fotos y vídeo al vendedor y ha procedido a reembolsarme el importe. Atención al cliente muy buena. Seguiré cargando con bomba manual o compraré en el futuro un compresor más potente y robusto.

VA BENISSIMO

This is a cool little compressor! It's definitely a small unit but it does the job! I've read that these units are loud and that's no exaggeration, it's noisy, but it only takes a few minutes to top off my gun. Hopefully this will stand up to the test of time. Run the fans before abd after the actual compressor unit as excessive heat will likely shorten its lifespan. I'd much rather run it for a couple of shorter periods than to run it too hard for one stretch of time.

満足!

Using it to recharge 480 cc bottle - declared for 250 bar (tested for 315 bar) - but in real world - never charging it more than 220-230 bars - usually from 150 bars or so .. It then takes less than 10 minutes roughly .. And - I always let it run about a minute WITHOUT LOAD (decompression valve OPEN) - to let compressor parts lubricate a little before actual work .. -- Watched some videos - early versions with "sketchy" electrical components - this is clearly addressed now - all connections are fine. -- NOTE: although somewhere in specs is noted "Schmieröl: ölfrei / Lubricating oil: oil-free" - near the end of manual (page 11 - "Maintenance" section) - clearly says you have to add a few drops of "100% treadmill silicone oil" in dedicated small port - every 5 fills or 1.5 hours use. -- I only made about dozen recharging so far - so - this is not "long time review" - but with that little maintenance and care - I don't expect much trouble ..