Feyachi Heat Resistant Brass Catcher for AR Thickened Nylon Cartridge Casing Shell Catcher Net with Quick Release Zipper, 2 Picatinny Rail Mounts - Holds 100+ Casings

Great. Works as it should. Adjusts to fit my ar15 and my ar10. Multiple calibers of each and it catches them all. Instructions are a little vague but it’s pretty self explanatory. Just undo all the Velcro strips before you begin and it will work a lot better. Holding 30 spent 223 just fine. 20 spent 308. I’ve only shot 10 of other calibers so I can’t say how many it will handle past that. Holding up good so far. The quick connect button is a little wonky at times but hasn’t failed to operate. It is extremely easy to use and easy to empty. Keeps brass in and makes cleanup after shooting non existent. Just dump it in a bucket and you’re done. Wish the pouch was a bit stiffer.

Great product. Second one I bought to have on several receivers. Works great and easy to remove quickly. Multiple mounting options for different setups. Saves alot of time chasing shells.

Alright. Why did I buy this? I'm a competitor who LOATHES loosing brass. I compete, I eject a casing, it goes who knows where, and now im short a piece of brass that I put way to much time energy into to perfect. I run one piece mounts which is the crux of this component along with scope rings that sit low to the rail. In my case there simply isnt enough room in any of my setups to mount this above the bell without sacrificing something. So if you're running 0MOA in your mount /w a 34mm tube, forget about it without compromising something. Also, the way the latching mechanism works, there wouldnt be enough be enough room to actuate the button to remove it without running into my mount. Setups with red dots work well. Storage -> For my use case, there is enough storage to hold at least 12 pieces of brass. For a stage for what I compete in, thats all I need. I could def get more cases in, but im going to eject every single one at the end. Directions - The directions are very well written. It's basically a two part system. You have one female end that stays on your platform, and a male end that connects in. The male end would only get removed if you were switching things around or wanted other empty the casings that way. There is a zipper opening on the bottom of the bag that being honest I wish wasnt there as it will likely get pulled and spill its contents. Nothing a zip tie wouldnt fix though. Durability - I expect it to last a season of moderate training / competition. I think thats worth the cost of loosing enough pieces in a batch of brass. I'll end up throwing this on my training platform to see how it performs long term and update if any negative occurs. Functionality and fit are going to be user depending. It sits close enough to the ejection port to capture. There may be a bit of timing with moving It along your platform's rails or its rails, but theres plenty of space to figure it out as long as you can maintain your eye relief. In my opinion, this setup is more suited for split rings than a one piece, but if you're willing to tinker you can make it work. My MPA mount wont afford this, so It will live on a practice rig. Still great value.

You can use use this on any picatinny style rail as long as their is clearance between the scope and the rail has the spot available for the mount. Also of course with open sites if you have a picatinny style rail. The base is easy to install and the catcher is easy to open as well as remove. Extra bases available is a nice feature so you can mount them on different firearms and use the same catcher. Brass catcher is nice if you reload to prevent dings in your brass or appease range requirements for picking up your brass. Works great on ar style rimfires that have a picatinny style rail to keep from scattering brass all over. The catcher is adjustable to position over the ejector port. Great price compared to many other catchers that need to be modified in some cases.

Very easy to set up and use. Works great. Did have problem after several uses, but contacted manufacturer and after explaining the problem they promptly sent out replacement parts to correct it. Extremely happy with product, it works great for MSR with rear charging. Easy to install and switch from one weapon to another. Extremely happy with customer service and support. They were very responsive and eager to help fix the issue. Yes I would recommend to friends and family. In fact I now have 4 of them in use with intention to buy for Granddaughter and daughters as well.

Fit my AR perfectly and makes clean up easy

Works well IF you have the right sight/optic setup to allow for the attachment point. If you have a low-profile optic or a one-piece scope base type setup, you probably won't be able to use this. Take note of all the stock pictures that show people using it with no sights on it. It works on a few of my AR's but not all.

Well made, easy to install, and it catches brass extremely well.

Works well on my 300BLK Troy Par, decent construction doest feel flimsy

Excellent unit! Easy to install and remove. Works well to collect the casing after firing. No longer have to collect off the ground. Simply to empty. Would recommend

Easy to install, a bit of a pain to get use to but saves time cleaning up in the range after.

Good adjustability and well made. Equal to or exceeds quality of much pricier name brand of same design. Priced more than fair for this product. .22 lr bolt action rifle bench rest shooting.

I just love it