YAARHEJ 2 Set The Desk Mount for The Flight Sim Game Joystick, Throttle and Hotas Systems Compatible with Logitech X56, X52, Thrustmaster T-Flight Hotas,T.16000M,TCA,Wining orion 2

I really wanted to find a HOTAS desk mount with adjustability, and this one hit the mark. I was initially skeptical about the split beams' stability, but the construction and assembly are rock solid--more so than I expected. These can easily support my VKB STECS and MCG Ultimate. (Side note about Gunfighter MKIV installation: the booklet suggests screw in positions that do not match this base--likely one of the older models--the second image are the points I found to work.) I would like to mention though, the clamp can interfere with the beam assembly if you want to adjust the height later on. I suggest moving the clamp down to avoid obstructing the height you want before screwing in the beams.

Mounts your sim controls exactly where you need them. Firm grip so nothing moves when it shouldnt. Caps for the ends of the extrusion do fall off from time to time.

The quality of the product itself appears to be of good construction. I would love to actually be able to use this product but I cannot assemble it with the screws/nuts they sent. The assembly screws are the wrong size. The smallest round head screws (#12 from their instruction manual) are too long to be used in the assembly. They also do not have the proper amount of round-head screws or slide nuts. They included a total of 10 slide nuts (see my picture). There are two desk mounts, each mount needs 10 for the base connection and 4 more for the custom mount section that attaches to the peripheral (Joystick/HOTAS). That means that I need 28, not 10. Update - I contacted the manufacturer and they are sending the correct screws. They have been very responsive 2nd update - They sent the correct screws and nuts. The product works great once I got it assembled!

Work great

I saw one video where it was floppy after being put together. This is not the case for my assembly. I would say mine is rock solid, so much so, that I’m afraid I may bruise my legs if I move them into them by accident. I used the parts provided with the kit and had enough of the special nuts for the proper assembly with two screws and four of the special nuts for the frame structure to attach the tubes. I also noticed that I placed one set with the pivoting braces opposite from what is shown in the directions. Both are study as installed, so I’m leaving them to see if it makes a difference as I use them. I have both VKB NXT EVO’s attached, one being the left hand Omni Throttle. It is after these were installed that my determination of a rock solid brace was made. My desk that I am using has a one inch steel tube along the edges and I used a one inch filler piece to match that tube height for the provided locking lever pad to brace upon. Again, rock solid.

Disappointed The product quality seems really good. It's nice and sturdy, however there is a serious issue with it. The screws (listed as #12 in instructions) are round which prevents the lower assembly from moving past the clamp when you are adjusting the height. You are only able to adjust the height either above or below the clamp assembly. Thr inly way around this is to remove one of the screws in the lower assembly which isnt a good idea. They really should have included flat screws for this purpose. This also prevents the product from folding for storage because the #12 screws hit the two arms on the side. The issue came up immediately during assembly and I spent probably 20 mins rechecking my work and the instructions thinking I was assembling it wrong. I wasn't.

Provides what is advertised. Both mounts were very straightforward to put together, and are made of solid materials. The mounting plates worked well for both my Winwing Ursa Minor and Moza MTQ Throttle Quadrant, both of which have non-standard screw mounting holes. However, these mounts smell absolutely horrible. They have the smell of cheap industrial grease right out of the box to the point where after assembling them I had to remove them almost immediately because sitting at my computer was unpleasant. I washed each and every piece with heavy soap and steel wool, only for the smell to remain. Turns out, the smell was coming from the rubber pieces (the grip for the desk clamp and the rubber stoppers on the ends of the arms). The coating also left a residue, so anything I touched after also had grease on it. Once I cut off the rubber around the grip and threw out the end caps, the smell dissipated. If you're going to buy these, wear gloves when handling them until you can get the rubber off and clean them thoroughly.

I've never used Monster Mounts or some of the pricier mounts but I can't imagine their higher price makes up for what you get with these. Those might better but for less than $100 these are almost impossible to beat. Using them with the TM Warthog HOTAS which is a pretty heavy HOTAS setup and they work great. If I had a complaint it would be that they aren't the easiest to assemble but if you follow the instructions and have half a brain you won't have a problem. Easier than setting up my bindings on SC or DCS.

Perfect, I've been using it for a month now and it's fantastic!

Super solid look nice !

1. Tag: Die Befestigung macht insgesamt einen guten Eindruck. Bei Belastung der Befestigung gibt bei mir sichtbar nur die Tischplatte nach. Die Befestigung selbst hat bei zweckgemäßer Belastung keine erkennbare Nachgiebigkeit. Die Kniehebelklemme rastet sicher ein und löst sich nicht unverhofft. Die Betätigungs- bzw. Klemmkraft lässt sich über eine Stellschraube am Gummipuffer oder durch Verschieben der gesamten Kniehebelklemme gut einstellen. Das Halteblech, gegen das der Kniehebel drückt, hatte ich eingangs als potenziell nachgiebige Schwachstelle vermutet, scheint seiner Aufgabe jedoch gerecht zu werden. Das Halteblech kam bei mir vormontiert an, die Schrauben waren aber nicht ganz fest gezogen. Die Verschraubung würde ich Benutzung überprüfen. Die Installationsanleitung sieht die Montage des Knotenblechs als umgekehrtes T vor. (ggf. Video ansehen) In dieser Einbaulage können jedoch rückwärtige Schraubenköpfe mit dem Abstandshalter der Kniehebelklemme kollidieren und zu Einschränkungen der vertikalen Verstellmöglichkeit führen. Es kann das Knotenblech aber auch als gekipptes T montiert werden, wodurch diese Einschränkung komplett aufgehoben werden kann. Im Paket enthalten ist außerdem ein nettes Sortiment an Schrauben, Flügelmuttern und Unterlegscheiben, die gut zur Montage der Joysticks und co. genutzt werden kann. Diese Sortiment scheint nicht beworben zu werden, ist aber definitiv nützlich. 2. Tag: Halterung passt übrigens auch problemlos für den HGP Shifter von MOZA RACING.

Otroligt bra kvalite, många möjligheter att ställa in

Produto começa a dobrar a base na zona dos parafusos do apoio da mesa, ainda só tem 2 meses de utilização. Acho o valor demasiado exagerado e o produto complexo para montar, demora bastante tempo. Quem não tiver jeito para bricolage têm um problema. A mim correu bem, mas demorou um pouco. Além do mais o cheiro a tinta marítima é muito intenso, os fechos vermelhos não são práticos para zonas da mesa onde nao seja completamente vão (que é o meu caso, tenho uma gaveta) então para ajustar nestes sitios é necessário prender a ponta e depois ir rodando até reposicionar. O fecho devia ser directo e na vertical. Isto produz que a borracha que é mal colada, tem-se vindo a descolar e a ficar separada. Portanto este produto não deveria custar mais do que uns 50 euros, e não 110