Siless Hybrid 3in1 200 mil 25 sqft Car Sound Deadening mat - Butyl Automotive Sound Deadener - Noise Insulation and Vibration Dampening Material

I recently installed the Siless Hybrid 3-in-1 sound deadening mat in my vehicle, and I’m genuinely impressed. For just $80 for 25 square feet, this product delivers performance that rivals materials costing twice as much — and with far less hassle. If you're on the fence......Just buy it! You will not be disappointed. Easy to Install: Unlike traditional sound deadening products that are stiff, sharp, and temperature-sensitive, this mat is soft, flexible, and easy to work with. I cut it cleanly with regular scissors and pressed it into tight spaces using just my fingers, so if in you don't have a roller or install tool, a good pair of scissors and your hands can get the job done. With other brands like Dynamat, the aluminum layer often leaves micro cuts on your hands and tears up your fingertips, but Siless does not due the acoustic layer being on top and above the aluminum layer that holds the butyl layer. So, it's very easy on your hands. Even in cooler temperatures (around 50°F), I had no trouble applying it but it goes on better heated. If warm outside, I would leave the entire box out in the sun for at least 30 minutes when it's warm or heats it's very pliable and easy to mold. Make sure its where you want it because once applied it's not ever falling off. and it became even more pliable and easy to mold. No heat gun, no mess — just straightforward application. I installed 40–50 square feet throughout the interior, covering everything except the headliner and the flooring forward of the rear seat. The difference in cabin noise is astonishing. I can turn my radio up concert loud with gut-punching bass, and from outside the car, it sounds like a factory sound system at mid volume. I was blown away by how well it contains sound — both inside out and outside in. My exhaust is pretty aggressive and now is barely audible from inside the cabin. While driving, it almost sounds like a stock factory setup. The Siless matting actually changed the driving experience and feels refined. If you're skeptical about sound deadening gimmicks, I get it, but this is the first product I've used and when I needed more, I went Stright to the 3 in 1 Hybrid matting and purchased it again. I love researching before buying and that's very uncommon for me to do. Note: Proper installation is key, and it does take time and patience. But if installed correctly and in the right places, it works better previously used from paint-on sound deadening to Dynamat. Update Nov, 2025 After using it this in 4 separate vehicles now. I feel the Siless’s 3 in 1 Hybrid has nailed it for best budget deadener that is better than dynamat extreme in performance and installation Protip: buy a roll of 2-3” aluminum tape and tape the seams. After trimming the edges tend to very sticky between the panels. I ran a strip of aluminum tape over the seems to create a better seal and true moisture I used it on four vehicles now and have I have not been paid to review and purchased every order myself. 3 in 1 Hybrid deadener by Siless is the best all around easy to apply sound deadner period!

This Siless Hybrid 3-in-1 sound deadening mat is easy to work with and feels high-quality. The butyl material is thick and pliable, making it simple to cut and fit into doors, floors, or panels. After installation, road noise and vibrations are noticeably reduced, and it also seems to improve the overall cabin feel. No bad smell. At 25 sq ft per roll, it’s a good value for anyone looking to dampen noise and improve car acoustics. Overall, a solid, effective option for automotive soundproofing. Used on a Fiesta ST.

Siless Hybrid made a huge difference in reducing noise in the floor of my truck cabin. In some areas, there was basically just bare sheet metal between the inside and outside, so adding this really helped the truck feel more solid and noticeably quieter on the road. I used Kilmat on the doors, and honestly I wish I had used Siless Hybrid there too, but it was too late by the time I realized the difference. This material is very sticky, easy to cut, and simple to apply, which made the install pretty smooth. Just a heads-up: the tacky side gets messy and will bond to clothing really easily, so be careful during installation. Overall, I’d definitely buy it again—great product with real results.

Very good sound deadener and heat shield, it is a bit sticky to work with, but easy to shape and cut

I have installed all kinds of insulation in vehicles over many years. I only needed to purchase 2 boxes to complete the entire interior siding of my 2025 chevy express, what a great value! I wanted to insulate my locksmith van for sound and heat. The sound reduction virtually eliminated the road noise. These panels also look amazing. It got up to 110F in the sun with the doors closed. After adding Siless insulation the temperature maxed out at 97F. That is a massive difference. Plus, I didn't even finish with the roof before testing. Siless Hybrid 3in1 was extremely easy to cut and adhere onto metal panels. I'm impressed with the quality of the individual panels and the adhesive is not toxic smelling compared to some others. My favorite thing about these panels is you can actually take them off and readjust them before they finally stick and they do not leave any black residue behind when you pull them up to adjust them. All I needed was a heat gun, knife and a roller to complete this job. The size of each panel is perfect, you can handle them with ease. I probably won't need your product again for a while, but when I do I will definitely be back.

I wanted to add sound proof material to the bare metal areas on the floor of my Toyota Tundra. The area behind the front seats had a haphazard application of sound deadening material. There were several complications to the project which may come up in other vehicles. First is the floor covering which had plastic pillars underneath to support any weight on the cover. The sound deadening material had to be cut out so these pillars would rest on the bare metal of the floor. This required a lot of cutting with a utility knife and at times heavy scissors. The instructions say to make a template before cutting the material and I did this for the driver's side. This doubled the amount of time needed to install it. On the passenger's side I laid the rectangles of material with the backing on and pressed the floor covering onto the material. This showed where the support pillars were, which I then cut out. Second is peeling the backing off the material. This can be very difficult as the adhesive sticks to it. The backing came off in multiple pieces and sometimes took 5 minutes for one piece. They say to wear gloves when handling the material but this is impossible when trying to get the backing off. Third is pressing the material onto the metal. The instructions say to use a roller, but this was impossible for the irregular surface I was working on. The hand is the best tool to press the material on. The material seems to be of high quality and I expect it will reduce the road noise in the cab.

I was sound and heat insulating a generator bay in my class A RV so I did three tests before and during material application: I did a sound level test to see how effective the material was for my application, a "stickiness" test, and a flammability test. This was indoors on a dry 78°F day. From beginning to end, the entire process, including testing, took 5 hours to install 25 sqft or material in a very complex area. One hour for cleaning, 3 hours for installation, and 1 hour for test setup and testing. Using a sound meter, I took before and after readings and determined that I reduced the sound level by 2.2 db (40% energy decrease) with a noticeable decrease in sound and frequency. The generator bay is located under the master bedroom in the aft portion of the coach. The sound went from a rattling, vibrating generator noise to a more tolerable low level rumble. The material was easy to apply. I did some testing prior to application and determined that surface preparation is key. I cleaned my painted metal surface and then degreased with acetone and the material stuck well. Be careful and purposeful when you apply the material because once it was stuck to the metal, it was quite difficult to remove or reposition. Since it was going to be installed into a gasoline powered generator bay located under our sleeping quarters, I did some flame testing to determine the level of risk. Although not highly flammable after installation, my testing revealed that the PE used will catch on fire under certain circumstances. In order to reduce the risk, I used aluminized duct tape to ensure that all the edges were sealed and the PE was not exposed to direct flame in the event of a fire. I also decided to install an automatic fire extinguisher as an added precaution. In all fairness there should be one installed in the generator bay anyway. All in all, I am very satisfied with the product and the results. I have recommended this product to my other RV owner friends.

Used on SxS back panel and made world of difference. Stuff is a lot thicker than most sound deadening and does a good job. Adhesive holds great if you wipe down with acetone first.

Product exceeded my expectations. I was replacing the carpet in the cargo area of a 2003 4runner, and thought I'd apply some soundproofing in the process as my rig (V8, headers, exhaust, AT tires) is a very noisy ride. I applied the mat to the entire cargo floor and wheel wells (interior, approx 20 sq'). I found the Siless product significantly reduced the road and muffler noise, even prior to applying closed foam and carpet over the area. I was expecting a modest improvement based on online research, but wow, way better than I was expecting. Quality product, fair price.

الي ازعجني إني كنت متوقع أنها أمريكية طلعت صنع في كازاخستان شي مخزي

Proper soundproofing for a great price. Not that butyl useless sound proofing sold everywhere

This stuff works very well, better than the Butyl (aluminum backed products). Why? because they are different material and the butyl only is for dampening rather than insulation even though it markets itself as both. Very misleading. I say this because I used 3/4 box of the butyl only product and heard practically no difference driving my GR86 (a noisy car as most are aware). Anyway this hybrid product is great. I did only passenger and driver side floors (front- to about where floor inclines, center- 3" onto transmission tunnel and inside sill (area under door just adjacent floor). I did drive the vehicle with only the R side done (as I worked on it over 2-3 days) and the decrease in noise was already noticeable. Note that this insulates / dampens high frequency noise very well, mid frequencies just fair, lower mid frequencies it likely does nothing. Do note I did insulate the rear passenger sides very well as this vehicle allows it (large void in front of rear wheels that likely cause a lot of noise). So the remaining noise is mostly from front wheel area and engine. I don't hear much exhaust noise until around 3k rpm now. The tin can sounds of the GR is gone. Note my purpose is being able to road trip this car, many focus on car audio so they may use the butyl only products more abundantly. My audio gear setup is high quality but I'm not aiming for slam nor high db so my treatment is sufficient.

I never put reviews but for this i was so impressed how good it works this stuff my trunk was so clunky with my sub it sound like garbage on the outside of the car now from outside it sounds like its not even turned up the rattling is all neutralized and then when you open the door its blasted the sub and sound proofing the floor of the trunk sides and trunk it self made the sub sounds more clean and punchy too amazing product highly recommend