Injection Bonding Adhesive - Fix Loose Tiles & Holloe Floors FAST Includes Patented Syringe Tip + Standard Tip + Anti-Clog Cap 300ml (2-Pack) NEW!

I used this to fix a long piece of laminate floor board that had dropped due to uneven under base. It drove me mad and this was the solution!Things you need in addition -1) Email from supplier (read carefully - instructions for when using the special ulta thin nozzle)2) 2mm Drill bit2) Wet, warm and slightly soapy cloth to hand3) Dry cloth and somwhere to place things if they drip4) Something heavy but safe to weigh effect board(s) down for 48 hrs5) Patience6) Care ;DDrill your 2mm holes into the gap of the laminate board at intervals where the sag is at it's worst. I did not use it where the boards connected fine (i.e right at the very ends), to avoid the liquid from pushing areas up that didn't need it.The 2mm drill leaves very small and hardly noticeable holes to apply the special nozzle and **gently** pump in the glue until it starts to naturally flow back out of the small hole you drilled. This is when it's reached it's correct fill. We were lucky to have boards that have a 'slighlty worn effect with natural looking wooden knots etc' - so I lined up these areas to help hide the holes even more.The liquid will keep coming slowly out of the holes once you apply weighted pressure to the effected board(s) which is when you can use the slightly wet warm soapy cloth and dry cloth in tandem to wipe the excess liquid away, including the nozzle itself. Eventually it will stop(!).*I found that if the liquid does not continuously pour out of the whole for a short while when board weighted, you may have not put enough it to create a solid fix underneath.The special ultra thin nozzle has a cap that prevents it from drying and can be used again. Very clever this!It worked well for us, good luck and take your time!

Nozzel leaked adhesive. Poor quality connection between plastic connector and metal injector ment the adhesive didn't go into the hole i drilled. Just down the side of the metal tip and all over the tiles

I've used these before they aren't that bad not the best on the market, but the one I got had broken tip screw and syringe needle which moves and pops out of its place. Not good quality materials and too bad there's no gun holder to go with it as well. This brand needs to fix the hardware and have better screw on and needles.

Like - the small diameter nozzle allows injection into narrow grout lines if used under ceramic tiles.Seems to have worked, time will tell, as this has been injected under two loose, clicky tiles, with a wet underfloor heating system.Instructions suggest using a 2mm or 3mm masonry drill bit........try and buy a 2mm masonry drill bit.Ironically, despite having 3mm masonry drill bits, I drilled through the grout with a 2mm HSS drill bit!..Don't like - can be messy, no matter how careful you are. You don't really know where it's really going of course, when injecting under tiles. This would be the same situation with a competitors productI ordered two tubes initially, to try ......Unfortunately, neither Prime, nor delivery to an Amazon locker was available for two tubes, would have been for a bigger quantity.The goods were sent by Hermes (Evri), who managed to lose the package.The supplier rectified this straight away, but still used Hermes, which meant that somebody had to be in to receive the goods, and with Hermes of course they can only tell you a delivery date plus or minus a day.......grrrreatOther than that we are pleased that it seems to have worked.

Complete Mess! Adhesive leaked out of the bottom of the tube and from the base of the tip, seems to be cheaply made? Not impressed, returned for a refund.

Review for Flloor-Fix Pro ORGINAL 300mlNeeded to reset a few floor tiles, but didnt want to pull up and risk breaking the tiles, as I cant get any close matches. This seemed to be the solution, followed the guidance instructions to help me fill a few voids which had formed to help reseat and fix the tiles back securely.

I bought this to fix some loose skirting boards and stair nosings around the house. The small tip is a game changer as I was able to get it into tiny gaps and the adhesive itself sticks quickly and seems very strong. I only used about 1/4 of the tube and it does indeed seem to remain fresh and unclogged. Excellent product.

No precision nozzle, this is the only reason I purchased this, now I need to take it back tk a store to return??? How is that fair