Moen Home Care SecureMount Grab Bar Anchor (Each)

First class anchors for a tile surround over sheet rock. Very sturdy and easy install. Note if using Moen bars, you don't need the plates that come with the anchors. It is rather obvious but the instructions on neither product show that. Do yourself a favor and order the exact hole saw you need especially for tile an start your hole with a small bit to make sure you aren't over a stud. Would definitely use these again. Good design, good product. Suction cup grab bars are evil and should not be used anywhere.

Why did you pick this product vs others?: Firmly holds the grab bar. Build quality: Solid construction. The Instructions are good - read them several times. Gather the right tools. For a tile wall you should use a stud finder with deep penetration ability if you're on a tile or porcelain surface; these are available that also indicate if wiring or piping are close behind the wall. Use a diamond hole saw (with pilot drill) even on ceramic tile and especially on porcelain. I've installed three grab bars so far and my diamond bit is still cutting and should be good for at least a few more cuts; cool the bit with water a couple of times on each hole you make. I encountered an obstacle on one hole and had to insert the Securemount with arrow pointing horizontal; once in place I was then able to rotate the entire assembly to get the carrier arrow pointing vertical as required. In other words, be ready to adapt and overcome. Be sure to cover the drain with a cloth rag - you WILL drop parts, guaranteed.

Expensive for a hollow wall anchor, but it's custom made for the Moen grab bars, and it works very well. I thought about using multiple toggle bolts, but I was worried that multiple holes would weaken the drywall. BTW, if you lose one of the mounting screws, its 10-32 thread.

I got 2 of the Moem Securemounts to install a chrome grab bar from Delta on a wall between studs. The Moem mounts have a flat aluminum plate that’s threaded to accept the supplied truss head machine screws. However, the mounting flange on the Delta grab bar is fairly thick with countersinks on the mounting holes meant for flathead screws, so the heads of the screws supplied with the Moem mounts protruded from the surface of the flanges. Even without using the supplied split ring washers the covers on the Delta bar stood about 1/8” away from the wall this way. I took one of the screws to Lowe’s and matched it up with a screw gage they had there, and they’re metric, M5-.80. Fortunately they had a pack of M5-.80x10 oval head screws, Hillman brand, that worked much better for my application. Now the covers for my Delta grab bar fit much closer to the wall than before with just a tiny air gap. I hope this is helpful for others who may need different screws than the ones that come with the Moem Securemounts. The mounts work perfectly and were easy to install.

Strong, smart, but have to be precise if using on both ends of the bar. Only item to be sure to have is a 1 1/4" hole saw bit. These are inexpensive, fit on any drill and usually come in a pack of assorted sizes. Used these the first time when installing the Moen toilet tissue/grab bar because these mounts came with that item - - easy peasy piece of cake. Later, I purchased the coordinating Moen towel/grab bar to replace an existing normal towel bar. I wanted this new bar to be installed in the exact same spot (in drywall) of the old towel bar so I wouldn't have a bunch of holes to patch. I purchased these mounts as an add on to give support as I knew I wouldn't be screwing into a stud. Important to keep in mind is if you want (as I did) to install in the same location as a previous bar, this means you will have the existing (smaller) holes in the drywall where the old bar bracket came off. This creates a problem when using your drill and the 1 1/4" hole saw. These hole saws are meant to hold themselves centered using a center drill bit, and make the larger hole relative to this center point. Because you already have an existing center point hole, there is nothing for the hole saw bit to hold onto and keep centered. I ended up taking the hole saw bit off the drill, and used a rubber mallet to pound it into the drywall deep enough so the teeth left an impression in the drywall and the hole saw bit would have something to grab onto. I needed the bar to be precisely in the same location because it was centered under a window. If this was not the situation and I could mount it give or take an inch or two, I would have placed the center bit just a 1/2" left or right of my existing holes. The 1 1/4" hole would encompass the old screw holes and the hole saw bit would still have "new" drywall" to drill through. A little more work and frustration this second time around, but the clean look and strength of these mounts make it worth it. * * update info on how to remove these mounts - Renovation of this bathroom meant that I was also changing out these grab bars for another style. My brother wanted to re-use these Moens for his bathroom so we commenced on figuring out how to remove them and keep them intact so they could be reused. We could find tons of YouTube videos on how to install, but nothing on how to remove, so here's that info for anyone who might wish to do so. Unscrew and remove the grab bars. Prying off the cover plates took a bit of delicate work with the edge of a small flat screwdriver. You need an allen wrench to loosen the bar from the mount. Once the grab bars are off, remove the screws that hold the mounting plate from the support insert. What you'll be left seeing is a thin round plastic ring around the big hole in the drywall. Use your fingernails to pry this ring off the drywall just far out enough so you can get a hold of it with your finger tips. Slide both thumbs into the hole and get a grip on this ring with your index finger. Wriggling and pulling out toward you, pull this plastic ring and arms out toward you. Eventually, the arms will click along the tracks and you'll be able to get the ring attachment fully extended toward you about 2" or so. At this point, if you don't care about reusing these mounts, just use a pair of snippers to cut the plastic arms and the support mount will just fall into your wall. The arms are still attached to the bracing piece so now you'll need to slide a finger along the top of the hole in order to push the vertical bracing piece to a horizontal position. I used my index finger, but my husbands hands were too large so he had to use a long screwdriver. Once the bracing piece is horizontal, slide your finger straight along the bottom of the hole to keep that piece horizontal and guide it (and the plastic ring/arms) out through the drywall hole.

These are strong and do the job when drilling into studs is not an option. Wasn't without its drama, as I dropped one behind the wall requiring me to order another one. Needs a fair amount of skill to install, but I eventually got it to work.

As advertised, good in theory but not suitable for my hand grab rail in bathroom. Will keep for future and make sure hand grabs compatible with bracket anchor

Easy to install. Didn’t need to find the studs behind the tiles in the shower. Mom needed a grab bar.

The anchor system is excellent and easy to install. Very solid, when you pull on it the wall moves not the bar. When installing just verify that any insulation is pushed away so as not to interfere with the attachment placement. Also no need to put caulking around the base it already has a preattached gasket.

For Moen "Secure mount" grab bars only.