EG STARTS 5X New 60mm Dome Shaped LED Illuminated Push Buttons for Arcade Coin Buttons Machine Operated Games DC 12V

The buttons are excellent! Seem to be durable and well made. They came in a pack of 5, with one button of each color.. red, green, blue, yellow, white. I did not do anything special when i ordered. I guess you can order all of one color, however i wanted different colors. it also came with 1 extra led bulb for each color, as well as 2 extra 'electrical units' (for a lack of better word). However, the instructions were a bit lacking, so it took a bit of trial and error on my part, as i am NOT tech savy when it comes to this type of electronics. However, i was able to piece everything together and make it work. for my application, i wanted to make a 'home game show' buzzer system. i was following a different you tube video on how to do something like this. my application is actually connected to an 'arduino' board, which adds to my learning 'fun'. i included some pictures to hopefully answer some of the questions that you might have regarding this product. at least i know that i had all of these questions prior to purchase, so i figured i might as well post them. Hope this helps :)

I've only tested one button so far, but works well. If the listing is not clear, these are momentary SPST switches. The switch/led piece is easily removable from the button and then the led is then easily removable from the switch, which is nice. Also, the LED is independent from the switch, which works perfectly for my use case. Obviously, if you wanted it dependent, you could easily jumper it. Came with some extra LEDs and switches which was unexpected The LED has a resistor for 12V usage As others have said, even at lower voltages (3.3v/5v) with the stock resistor there is still enough current flow to light it up. However, it's easy to swap out, as its just soldered on to one lead to the LED. Swapped in a 100R one (lowest I had on hand) and it lights up great off a 3.3V GPIO pin on an ESP8266.

Works well. Took me a long time to figure out how to remove the switch so that I could mount these through a hole.

Good quality switches. They came in time and were enough to complete a project. Used them for credit button on pinballs. You can insert labels in them too.

Almost perfect. First off, I would like to say that the buttons are really good and just as they described. I had some problems with the LED not working (5 out of 10), but the seller was very quick to respond to me by email. The fix was just to reverse the LED because the polarity was switched during assembly. It was really easy to fix just bb flipping and reattaching the LEDs. Each LED is actually colored, along with each button. From my pictures, they light up pretty well. However, the yellow button looks like it uses an orange LED even though the LED is colored yellow as well. And when lit, it shines orange. You can see it in the picture where I put 2 yellow buttons side by side. I moved the white LED over to the yellow and it does a better job of keeping it yellow thanks to the colored dome. I might just go out a buy a white LED to fix this problem. The buttons click every well. And I'm having a great time playing with the project.

Everything I wanted when I ordered these buttons. Pretty clicky. Some LED’s are brighter than others (namely green) but it’s not that big of an issue. They have 4 terminals: 2 for the button and 2 for the LED. It can be a little difficult to install the LED’s, but they include extra bulbs in case the worst happens. I used 3.3V to power them, and while they weren’t super bright, what else can you expect when you use almost a quarter of the voltage the seller recommends. I was just happy they still turned on. Overall great purchase. I’d recommend these to anyone looking for large buttons.

Bought two sets of these to make a Pop'n Music control panel for an Arcade1Up machine. Wish I had a full sized cab so I could use the bigger button, but these worked out surprisingly well. Buttons look great and work just fine. Now if only I wasn't terrible at the game.

Worked with the USB adapter I got from Microcenter, only needed the 5V power to light everything. I changed the white light into an orange one by replacing the LED inside the housing. Works great, very sturdy. I used them for an original art installation project :)

are package was missing the 5 micro switches entirely. was very disappointed had to return and re-order

Me agrado la construcción de este producto, y que cuenten con repuestos de los leds y los pulsadores. Para que emitiera más luz los leds modifique la resistencia interna que incluye y la cambie por una de menor valor. Es fácil sacar el led de la base.