Triptis Floral Armless Accent Chair with Attached Cushions, Fabric Upholstery, Wood Legs, 16.63" Seat Height, White, Blue & Gray

Very pretty, but I wish that I would have checked the measurements out before I purchased it. I just assumed that it would be normal height. It’s alright if you are 5’3” or shorter.

These chairs are nice for an office but too small for a living area but make nice decor for those who like nice additions to rooms

I love this chair! I didn’t really care for the curvature of the back legs…at first….but now, I see that it adds to the uniqueness of the design. I wanted a different view when I entered the kitchen from the garage. The area is actually a breakfast area/laundry room combination. As you can see from the first photo, the view was not welcoming and definitely lacked the ‘wow’ factor. So I moved some things around and purchased this chair to ‘seal the deal’.It does require assembly and the instructions say two people are needed. I suppose you will need two people if you don’t have 30 minutes to invest, which is how long it took me (ALONE) from the time I dropped that first screw, until I placed the finished product in its final resting place. It was hilarious! I’d pulled out my tool bag and laid everything out on the living room floor: hammer, Phillips screwdriver, wood nails, etc. DIDN’T NEED ANY OF THAT!! Allen wrench and screws were already provided and that was ALL that I needed.****VERY IMPORTANT!*****The screws are grouped together by a rubber band. If you pull those out carefully as grouped, all you need to do is drop each set (bolt, nut, washer) in the specified slot. So happy with it that I really want to purchase another with a different pattern for another room in my home! It took me longer to write this review than to complete the assembly.😂

Very cute chair but check the measurements this piece sits really low. Almost looks like a youth chair. Cute pattern and sturdy enough but super low.

The chair arrived yesterday and looks nice enough when assembled--just as in the picture on the website. Have no experience as to wear or sturdiness, so I'm basing the review on initial observations.The problem is that the assembly process turned out to be difficult. Theoretically this involved putting in 12 bolts though pre-drilled holes (2 for each leg) and four more to connect the back to the seat, using a provided Alan wrench. In practice it was difficult. Aligning the holes in the legs and back with the metal sleeves where you could screw in the bolts was a little tricky, but manageable. But then screwing down the bolts was time-consuming and tedious, because most of the holes were close to a barrier, so you kept having to remove and re-set the Alan wrench every half turn or so, and there were about 20 turns per bolt. A ratchet wrench was really needed and it would have saved a lot of time if they had included one of those.But that was only the beginning. The instructions say that you shouldn't screw down the bolts for the legs completely until the chair is assembled and you can set it on the floor and adjust the height of the legs so that the chair its level on the ground. This makes sense, except for two things: First, the legs have virtually no play since the bolts holding them are going through a hole, so it's impossible to move them up or down more than 1/8", if that. But, second, and worse, you can't screw down the back legs at all after the chair is assembled because they are part of the back assembly, and once you screw the back to the seat, you can't reach the bolts to tighten them. So you pretty much have to batten down the back legs before you assemble the chair, which is what I did.When I got done and put the chair on the ground, it looked like the front left leg was about half an inch short. I tried adjusting it as much as I could, but there was very little play. Do as I will, either the left front leg was too short or the front right leg was too long.I worked on it for a couple of hours and what I finally had to do is to take off the front right leg and drill out the holes to make them into a slot, so that leg could move up and down. This worked, and it had the added benefit that the chair seat now rested on the shoulder provided by the leg, whereas previously there was a gap. However, the left leg still has a gap. It's hard to explain this, so I'm including pictures. The one without the gap is the one I adjusted. Prior to my adjustment, it had a gap even bigger than you see on the other one.This is not an expensive chair so I can't complain too much about the fact that everything isn't flush. But they really could improve the product if they actually allowed some play in the legs so they could be adjusted up or down for levelling--of if they cut them more precisely so this wouldn't be necessary. A ratchet wrench--even a very cheap one--would also be very helpful.

These chairs are very comfortable and adds a nice touch to my living room ensemble.

I got this chair for an office/den area. As others have said the assembly was complicated by tight areas and no clearance to make full turns with the provided Allen wrench. What should have taken about 8-10 minutes took about 30 as a result.The quality isn't bad for a chair of this price point and It seems sturdy enough. The fabric is decent enough and it isn't bad to sit on either. But it really is hard to describe how low this chair sits to the ground without actually seeing it. I will probably keep it as it is mostly for decoration and I don't want to spend much for this room which gets little use. However, if this was any other room, the chair would be going back in a heartbeat due to the size.

Is nice, pretty color

Bought this chair for my Elkhound so he could look out the window! Ashley furniture is definitely known to be price point driven and disposable, but this chair has impressed me! I work at a furniture store and actually ordered this chair from Amazon because it was cheaper than my staff discount. I expected some type of used knock off to show up and I was pleasantly surprised! Appears to be legitimate Ashley product, great price, and has held up well. Cheap and cheerful :)

the colours are darker and more flashy then the picture

I bought this chair as a discounted item, probably returned because the colour is not the same as the picture online. To me it doesn't matter because I like this colour, it's more teal, sage green, black & gray. Very comfortable, beautiful quality fabric, would go in modern or mid-century modern style home. I love this chair for doing needlework because it has no arms to get in the way. Don't be afraid to buy discounted furniture on Amazon, this chair was in excellent, new condition.

Nice chair. The chair was quite a bit smaller than expected though. More a childs height.

This is a cute chair I bought 2 for my mom! But when we put it together one of the screws comes out into the cushion.. very upsetting having spent over $400