QUASCO Front Rear Motorcycle Turn Signals, Mini Size Led Brake Tail Lights Universal Compatible with Harley Honda Suzuki Triumph Yamaha

The media could not be loaded.  FIRST OFF. before you test them, and think there broke or junk,, Test the supply wires with a bench test and low amps, and a test light.. WHY?? BECAUSE THE BLACK WIRE IS NOT GROUND!!! (IF you DO hook the black too power, it wont burn them, -Well myne didnt) but they wont work...Like on most japan bikes, The BLACK wire is usually the 12v POWER+.-SAME W/ these lights..But red and yellow are also power 12v+.. WHITE-GROUND.BLACK- PARK/RUNNING-(Dim RED-Rear).RED wire is STOP/brite)YELLOW WIRE+ TURN-amber LED)But..Awesome little lights.. think they could do a tad bit better on price.. But its fair..you have Every light mode you need except, for a liscense plate light.. Turn, stop, park.. Bright.All in All, FAIR QUALITY.And Wires are atleast faily big enuff' too strip' and splice. And wire is actually more of a Automotive grade like itshould be thankfully...- Don't tighten the heck out of the nuts (btw which are 13mm? or 1/2"? IIR, just snug'them.. Seen them break easy, there smaller dia' 8?-10?mm studs? These seem better then others thou. But LILL' Loctite be good.Also mite need and Adjustable-speed flasher relay, I had one already.. the orange?> ones work decent. Unlike some other LED' signals that are rectangular Bar shape, these dont have a flashing-flowing mode built in, like some do.. NBD for most Road bikes anyway.. But if your putting these on a offroad vehichle, Youll need the flasher relay..(other cheap "flowing bigger styles flash on there own w/ 12v power)OK, SO, Depending on the angle, the RED, STOP CAN' Over power the trun signal a TAD bit..- Its still easily seen, But depending on how you mount these, the red row can be on top, AMBER bottom.. Or flip them to other side, and vice versa.. Youll see..I noticed if you make sure AMBER is Mounted on top' and red on bottom, then turn them down towards ground a tad' THEN,the amber is more visible for signals (for rear) havent tried front yet.. Either way they are bright and work great..- IMHO, I think a Seperate red STOP Lamp in the middle looks better, Or down on your axle like a bobBER, And then just use these as SIGNALS, An markers,.. just my 2cents..Oh yea, I would grab some Heat shrink tubes, after there bolter in place, Put a heat shrink tube OVER the wire harness, and up onto the Threads of the stud, and bit of wires that are open in stud, too keep all grimme' and water etc outt of the threads and stud wire hole..ill post and update after a few weeks.. but so far so good..

Love the size and the how bright they are

I mounted two of the amber ones on the front of my Roadstar in addition to the existing turn signals for added visibility. I then mounted two in the rear of my bike along with the brake running combos. the only reason I did not give them 5 stars is because I wish they made a light dedicated to only the break function instead of a break running light. Regardless they are still plenty bright, and any added visibility is better than nothing.

Works great

The lights are very small and almost blend in to a motorcycle frame that is black. They are very bright for the size and are more easily seen than the stock turn signals on my SSR Motorsports XF250X (Chineses dual sport). All I had to do is purchase 11 male and two female bullet connectors and some heat shrink tubing. I used 1 male and 2 female bullet connectors to make a Y connector to connect the rear turn signals as running light using a spare connector that already existed. I could not use the brake light function because Pennsylvania does not allow 3 brake lights on a motorcycle.

I read a lot of reviews and they said it was bright and i though mhm yeah right... they will blind you if you stare at them from 4ft away in daylight in florida...just saying if you are questioning it....DO IT.

Installed this set. Super bright and happy with the size. 100 times brighter than factory on my harley.Only down fall is got pulled over and harassed about them not being DOT approved.perhaps they are and I cant find proof?

I tried a cheap ALT to other brands and I can tell you, this one went too cheap. It is not bright, made of thin plastic. I should of returned it when I first got it. Spend a few extra dollars and get the better ones.

Gran iluminación instalación sencilla recomendable para personalizar tu moto

Installed the two rear multi function led lights, was a little apprehensive because of the size but once installed they are super bright compared to stock.when changing from incandescence lights to led, Remember to flash the ECM ( electronic computer module ) and reset the error code ,If your not sure how to access the ECM, please take vehicle to your local dealer and have them do it, the whole process took me less then an hour on my harley

One of the lights is super bright and the other is really dim. It works if you wiggle the ground but I assume it was poorly assembled. Super happy with the bright one but one signal light doesn’t do me much good.