Black Motorcycle Trunk Tour Pack Luggage Compatible with Harley Honda Yamaha Suzuki Cruiser Tail Box Top Rack Backrest

Holes are easy to drill, and can be located from opening the unit for both bottom mount and rack on top. Smaller than a stock harley tour pak, but MANY hundreds of dollars less. Nice gloss black finish, chrome rack on top is nice. Holds my full face helmet with a bit of room to spare. I'm very happy with it. Well worth the money in my opinion.

Small size Davida helmet fits and lid closes but not the HJC C91 modular.Back rest mounts easily in pre drilled lid holes.Top rack, if using, has four mounting locations molded on inside, used a 1/4" brad point drill from inside lid with blue painters tape on outside to protect it when the drill goes through. Started four screws before tightening with 5/16" nut runner. (Remove rubber feet, install rubber washers first)Do have to push in on lower latch/box in order to get it to close tight enough to be latched. Hope the latch holds up, as the top lid catch has loose rivets.Looks like provided hardware to mount on my BMW R60/2 luggage rack will work well and will update with photos later.

I mounted this trunk to a Harley quick release mount for my Softball Slim solo. It sets directly over the rear fender and provides the storage for when I go on long trips. With the quick release mount I can take it off when I get back and switch to the fender rack or passenger seat in seconds. The trunk is light weight but works perfectly for my usage. The included rack need extra work to drill the holes and mount because the trunk lid is not pre marked or drilled for the rack. It is an excellent deal for the price.

For the price they charge - i would say this is an excellent value. But you do not get what you do not pay for. for the price - it does the job. But some ofteh cons include. 1) There are no directions on how to mount the chrome rack on top of the tour pak - it took me a while to figure out how to do it and once I figured it out, it was easy. But come on - just throw a sheet of paper in the box guys with directions. 2) the back rest is at a strange angle and not 90 degrees to the seat so it is comfortable ( I plan to angle the entire unit at a down angle somehow to compensate for. this). 3) it is weak/flimsy construction.how I mounted the wire rack - removed black covers from four mounting post on the rack. Attached painter's tape top of the tour pak in areas where mounting posts of rack will sit. placed rack on top of tour pal and used a marker to mark painter's tape around the entire diameter of the mounting post. removed rack, drilled holes in areas I marked. removed painter's tape. placed black rubber caps with center holes over mounting posts on rack. Attached rack to tour pack with provided screws and washers.

I almost expected this to be lower quality than it is considering the price, but it has overshot my expectations. It's pretty high quality considering that its under $100. The latch works pretty well, better than other cheap luggage carriers. Its universal, so mounting it will just depend on your set up, but it looks good on my 99 Honda Shadow 600 VLX. There aren't any holes in the top for the rack, but I kind of like that in case you don't actually want to install it. If you do you'll have to get creative with a pencil and a piece of paper to outline the holes. Best part is the seller is super responsive in the case that you have issues.

Had to do some fabrication to get it on right

I liked the fact that is spacious enough to fit a full-face helmet. It looks good and is easy to install. That said, you have to be mechanically inclined to be able to work any differences from your bike luggage rack and the hardware provided. One thing I would recommend to maker is to drill the holes on the bottom of the trunk evenly horizontally as well as vertically. My luggage rack only has the chrome tubes running from front to back, so I had to use the brackets horizontally (left to right), Unfortunately the brackets provided only fit the holes vertically (front to back) so I had to purchase hardware to make it fit. This can be easily fixed by maker by drilling the holes in a square fashion so hole distance from each other are the same in any direction. One very important thing that made me re-mount this thing, make sure that if your Bike has saddle bags, that they open freely before you secure this trunk, otherwise you'll have to manufacture or purchase a rack mount that can flip the trunk back so you can then open the saddle bags,

So nice to have extra storage. My wife says the seat is comfortable. I installed it by slipping hose clamps between the box and the flat brackets that were included and tightened them to the luggage rack on my bike. I put two hose clamps on each side and it's very secure. Hope this idea helps someone. The rack on the top gave me issues. Only 3 of the 4 bolts would thread. I had to make a trip to the hardware store to get a longer bolt. I think it's because the holes have to be drilled perfectly to avoid this issue. I made a paper template to get the holes as close to perfect as I could, but human error prevailed. The rack looks great and is relatively easy to install.