HUANUO Triple Monitor Mount for 17 to 32 inch Screens, Adjustment Gaming Triple Monitor Stand with Swivel, Tilt, Rotation, Clamp & Grommet Kit

It's awesome! Holds up all 3 of my monitors perfectly. Installation was easy since all you have to do was follow the instructions they gave you. Super nice quality and fits well. Has a very sleek appearance as well. Overall, definitely worth the money.

I needed arms that could extend monitors out on a wide desk. These do a very good job at that. They also make a single arm and it's parts interchange with the dual and triple setup. While these will allow great reach for most desk, I have a wide desk for full sized drawings. So I bought a Triple setup and a single setup. This allowed me to do three monitors TWO on the triple arm and ONE of the single arm. This gave me extra arms to use to extend my monitors. It worked great. They have built in cable management that works very well. The arms have plenty of adjustment they you can lock. The only issue I had was the tension set at the factory is set pretty high probably to avoid getting complaints about the monitors drooping. Once I figured out that I needed to greatly reduce the tension to find the balance correct balance it held the monitor in place really well. I can move the monitor around and it just stays where I put it. I used the desk clamp. Its very solid. I even got a separate laptop mount to hold my laptop and docking station and it holds that well too. This unit is very sturdy. It also has the a place to keep the adjustment tools on the post. You can lock each section down so it doesn't move but I didn't find the need. It just stays where it's put. I'm very surprised at how well these work and how easy they were to setup. But read the instructions carefully which are very well done and the parts are labeled really well.

I decided to go with a 3 monitor setup rather than my usual 4 monitor setup (2x2) as I wanted to reduce having to look up at the 2 monitors above. My monitors are 27" and when trying to do a horizontal setup, there is just too big of a space in between monitors. Meaning, if I put the third section of the outer arms in, they are just too spread apart. I could adjust this, but the arms would then hit the wall so I would have to pull my new desk out further, which I don't want to do. For now, I had to rotate the two outer monitors to vertical, which dims the screens a bit and messes with the resolution. I also wanted to make sure that the mounting bracket to the desk doesn't damage the desk. The box does not come with sufficient protective pads, so I use the round rubber peel and stick rubber feet from a switch and that seems to work fine. No slip, but over time this might leave a mark so I'm looking for something better for that. My only other options are to get larger or smaller monitors which I'm considering doing as I need move toward 4k monitors for my content creation work. Final thoughts: The mount is nice and the cable management easy. Installation was easy. Works well on my L-shape Autonomous desk. I will need to change my monitors to larger or smaller. Smaller than 27" would use two sections on arms for horizontal layout. Larger than 27" would use three sections on arms for horizontal layout. They need to provide better padding for the desk mounting bracket. Price is okay.

Great quality for the price. I attached several pics and a video of it mounted to my electric sit/stand desk. I did order a thick metal plate designed for these mounts to sandwich on the desk being that my desktop is particle board I was concerned it would snap the desk where it clamps on at. I’m running 3 older 24" dell IPS monitors that are a bit heavier than most newer monitors and it handles them just fine. The gas powered arms were a little tricky to get adjusted just right and I still have one that needs some tweaks. When I adjust the screen menus with the screen buttons the monitor will slightly raise up on its own. Kinda annoying but I have not found a way to lock the arms in place once you have them setup the way you like. There is also only one screw underneath on the clamp and can be somewhat difficult to get tightened as the entire unit wants to turn. There are other units out there with dual screws that look like they would work better and prevent the headache of turning the entire setup when tightening. Not to mention they seem more secure. The cable management is great as I have two separate inputs going to each monitor and the power cable. All fit nicely in the sleeves and clips. Lastly there are no input plugs on this stand. Not really a con as you can clearly see that in the pictures and not docking any stars for it either. However there are other units out there that have built in USB ports, mic ports, etc that run around this same price point. All in for the price I would absolutely buy again and has been rock solid for a little over a month now with my sit/stand moving up and down multiple times a day with no wobble. Oh and the detachable vesa mounts that just clip into the arms are an amazing thing when installing your monitors. Just buy it. Hahaha

The stand is fairly easy to assemble. Just understand that this isn't something you will be putting together in 5 minutes! Expect a good 30 minutes to an hour. You can do this as 1 person. If this is going on a wood desk or a glass desk, be cautious! This may crack or damage the desk! They sell a metal plate for the glass desk as well as for the wood! If like me, your desk is wood with uneven surface, you may want to take an old mousepad and cut it a little larger than the foot and use that as a 'matt' for under the foot of the top and then use a plate (purchasable) for the bottom to protect the desk from damage. I used a small piece of wood being my desk was up against a wall and it hides the piece of wood. Once the foot was secured and the central mast was solid, not going anywhere then the arms were able to be put in place for the monitors to be put on with no damage to the desk. The only 'complaint' I have is the central monitor's limited positioning. It is virtually fixed to the mast. There is no moving closer (away from you) or towards you (away from the mast) to adjust the view for comfort. On each point on the arm there are lock screws to fix their position. This helps with their sturdiness however it doesn't help with the monitors themself. If you want to 'fix' the monitors themself, there is no way to do that. Bump them, and they can move a little and you are now working on getting them just right again. Overall, I am very satisfied with the stand, all the accessories offered FOR the stand, and the price. They even offered a mount bracket for my monitor that had no VESA mount to convert the desk stand mount into a VESA mount!

Overall I love this item and unlike my last purchase, which I had to return, I plan to keep this one. PROS: Has two extension arms, meaning you have the middle part that connects to each side, plus an arm AND an additional arm, most would only have the middle part and one extension arm. This means for guys like me with 3 32" monitors you have the option of having them sit horizontally without having to sacrifice, IE one monitor is partially blocked by the other. As I noted I had to return a different brand and that was because of this. Weight - My monitors are roughly 15 1/2 pounds each and I didn't have any issues moving the arms around with the monitors connected. Says a lot about the stability that I'm talking about this product being able to hold a 15 lb monitor on a second arm extension, as opposed to one. Install time - About 10-15 minutes, 20 if you factor that I'm a moron who didn't check placement before setting everything up, then forced to disassemble and reassemble in the proper area. Bad joke aside was straight-forward setup but use your own screwdriver, the one that comes with this is limited. Range - Similar to what I've used in the past. Easy to lift upwards, downwards, tilt the monitor, rotate to portrait. Standard stuff CONS: Only one. The middle pole is a decent size, but not tall enough for me. If you're like me you want your monitors higher to reduce strain on your eyes (I'm 6' so I prefer not having to look downwards so much). In my situation even when I had the middle area at it's highest my middle monitor was too low. I ended up using a stand for my middle monitor instead of connecting. Checked with the manufacturer and unfortunately there wasn't an option to buy a taller stand or add an extension, so while I give this 5 stars IMO it's really 4.5 and only because of this limitation. TLDR - Great product, no regrets purchasing it. Can hold 3 horizontal 32" monitors but middle might be lower than you prefer.

Yes I am giving this item one star to catch your attention of the monumental task your about to place onto yourself. Do not buy this type of triple monitor mount if you are faint of heart. This thing will test you to your very core and bring you to your knees, but it works great once you make it right for you if you can master it and show it whose boss. Yes I realize I may not be using it it in the perfect way, but this thing is an akward nightmare that is almost sentient. I have made it work and am using it to max capacity, but it has been quite the experiment to get it to a stable enough point where I can justify this is better than using the stands my monitors came with. It's been lots of trial and error, multiple busted monitors, lots of experimentation, lots of reinforcement, and lots of fine tuning. I work from home and have attached 3 32 inch monitors to this thing all horizontal. Whitch I do not recommend because while the description says it can support that, it really limits the range of motion of the 2 adjustable swing arms and you have to be careful not to bang the monitors into each other when adjusting or careful not to bust the screen of your middle monitor with the corner of the side monitor or just destroy the inner monitor corners all together. With 3 32 inch monitors this takes up the whole with and then some of 6 feet. And I can not pull the side monitors as far inward as I would like to get more of a half circle effect. Like other reviewers have pointed out, the C clamp really puts a lot of pressure into a very small area of your mounting surface. You can drill a hole in your desk but the hardware seems a bit thin to do this. Hindsight, I would have given more consideration to wall mount options. Because I like lots of surface space, no drawers, and simple solid wood tables are pricey and a dining table as the desk I would need would be ridiculous; l opted for a 6ft plastic folding table as my desk. I made sure to buy some metal C clamp reinforcement plates before setting this up for the first time. There was so much downward force from the C clamp, this contraption would have caved in the table and twisted it in half if I had let go completely. I did a little bit of wood working on a 2x6 scrap for the bottom of the clamp and used a thick plastic cutting board for the top of the clamp. And then added in the metal C clamp reinforcement plates for good measure. Trust me, it actually looks decent and not ugly like it sounds. I also mounted a clamp to the wall to grab the middle pole to keep this from ever falling forward (later on, I made it months ago but never mounted it to the wall until after the events below like an idiot). After using this set up for a few months, I noticed the C clamp was slipping away from the table. Like a moron, I did not remove any of the monitors before readjusting. I had my wife keeping things stable while I was under the desk to readjust the C clamp but the whole assembly fell forward and while she caught it, 2 of my 3 LG 32 inch gaming monitors got busted. I had to purchase replacement monitors but made sure to take a metal handle and run it across the backside of the C clamp and secure it to the 2×6. This way the C clamp cannot back away from my desk without taking the whole 2×6 with it. Then I added my security clamp/mount to the wall as well. This thing comes with plenty of spare hardware and parts to fine tune it to suit your exact needs for what you mount to it. Assembling it is a nightmare and the the directions would do a better job as bird cage lining. Pay attention to each arm segment. While all 4 looked the same, they are not and the directions will have you a bit off kilter. I had to unassemble and reassemble several times to get this thing right. Carrying this thing is about as easy as carrying a lifeless metal robot with heavy metal arms swinging every where ready to destroy anything in your path. Trying to add or remove one of the side monitors is rough as the spring loaded arm will fight you and it about takes 2 people to add or remove a monitor. You mount a versa plate with a plastic block attached to it that slides into the mechanical arm, but the arm moves up and down when trying to get it to lock into place. It's especially fun to remove a monitor as the spring loaded arm will keep popping up and relocking the monitor in place. Hence why I said you need 4 hands. You can adjust the tension on so many diffrent places that it's great for fine tuning. To wrap this up, this thing works well if you have the determination of a warrior but at times it can be like arm wrestling an octopus. I have 2 other mounts made by this brand and they have been fairly easy to work with since I am not pushing them to the make like this hefty boy. It is nice being able to grab a monitor and hoist it up in to the air to demonstrate things on the screen to a bystander. This is also a good option for a standing desk as you would just need an elevated surface for your mouse and key board because the monitors can lift pretty high with a baby's touch. So think long and hard about purchasing this, but it's a good unit and made well. I'm only giving it one star because it's been one **** of a fight making this thing work the way I want it too and using it with 3 32 inch monitors and a plastic table is a fool's errand but I was determined to win this fight.

Well constructed and monitors are perfectly aligned and sturdy.

I have used this for a couple of years now and i love this stand. It has a very strong build quality and is easy to be put together. The range of motion is flexible so you can change the monitor with ease.

After doing lots of research on monitor stands and solutions for three monitors, a lot of people recommended using three single monitor arms instead of a triple monitor mount due to stability issues found with a lot of triple monitor arms, especially as I was mounting three 27 inch monitors. I really did not want to go down this path as I wanted my setup to look as clean as possible without too many arms being mounted to my desk. I decided to risk it and order this triple monitor stand after reading some positive reviews. It arrived and it took me between 1-2 hours to set up which I thought was relatively reasonable given I had never set up monitor arms before. Installation went very smoothly, there was a worry that I may damage my Ikea worktop as it is veneer with particleboard (which the instructions for this mount said is not a suitable desk to mount on), but I decided to go ahead anyway. I did add a bit of hardwood between my desk and the clamp to give it a bit more strength and so far it has been perfectly fine. The mount itself is super adjustable and very stable. I've managed to get all three of my 27 inch monitors perfectly aligned, and there is enough space to angle them inwards. You could probably fit 32 inch monitors on here quite easily. I have had it all setup now for about a month and the monitors have not shifted even one bit. The outer monitors do wobble a little bit if my desk is wobbled or when I raise/lower my desk with the sit/stand feature, but its not a lot of wobble, and during normal usage (such as typing on my keyboard) they barely move. When they do wobble, they always return to their set place and do not shift at all. Having switched from using the stands that come with the monitor to this triple monitor arm, I have gained so much more desk space and my setup looks super clean and professional which is exactly the reason why I purchased this mount. If you are in a similar position as me, and are not sure whether this mount will suit you, I am sure you will be very happy with your purchase!

Llegó a tiempo, excelente conductor de entrega y el producto funciona bien, paciencia y un poco de tiempo, bastante simple, método de ojal para mí y muy bonito. arrived on time, great delivery driver and product works well, patience and a bit of time, simple enough, grommet method for me and very neat looking

Easy to assemble Can hold my very heavy 36" monitor with no problem.

Génial !!! Super bonne qualité et montage très simple, je recommande.