Large Aluminum Heat Sink 2.71"x2.71"x1.41"/ 69x69x36mm Heatsink High Power Cooling Plate 27 Fin Radiator GPU Cooler IC Module PC Computer Led PCB Charger Electronics Amplifier

For $8 dollars delivered it's pretty nice. Very smooth face, fine fins that actually serve to dissipate heat, fine end cuts with no jagged edges, just the right size. Unless you absolutely need something actively cooled with heat pipes or skived copper: this is your clear winner for intermediate size, high quality, passive aluminum heat sinks. Just be sure to arrange the fins vertically so you get a little convective cooling boost from warm air rising.

Very handy heatsinks, nicely made and goes well with my Mac Mini and SSD drives. I use the heatsinks along with an aluminum 1/8" thick base plate to cool down my computer setup. They really help to lower the equipment temperature and keep them running below 85 degrees F. Well worth the value investment.

Very nice quality heat sink. Easy to work with and tap 3mm holes for MOSFET screws. Keeps the amplifier nice and cool!!

I put two blocks of them on an aluminum tray of water, 2/3 soaked in the water, on top is my MBP, works great. However, the tray and fins got oxidized and are very hard to clean. Many clusters of white powder like stuff are found in the water. I hope they could have some special treatment on the surface of the aluminum and it's safe to soak them in water.

This heat sink works well for me and I would buy it again.

This was highly effective at taking the temperature down on my Sabrent 2-bay SSD enclosure.

The fin count and fin aspect ratio of this heatsink is impressive, especially to us old-timers that remember a time when heat sinks with this high a surface-to-volume ratio had to be made by edge-embedding sheet fins into a milled-slot carrier. I found a dimensionally-similar (2.581" wide instead of 2.71", 1.340" tall instead of 1.41" tall) heat sink in an online AAvid catalog, model # 83220. The AAvid heatsink specs were 1.01 oC/W/3in (still air), so I'm expecting this heatsink could be 10% better (lower). Note that if you bought a length other than 3", the thermal resistance does not scale linearly with 1/Length, assuming a centrally located thermal point source. For the 15.75" length I'm using, the improvement is only a 50% reduction in thermal resistance. Also note that the thermal resistance decreases (improves) with moving air. While the documentation I found for the #83220 did not provide thermal resistance versus air flow, I found another AAvid catalog and heatsink #72070 (dimensions 3.008" wide, 1.02" tall, similar fin aspect ratio, 1.4 oC/W/3in) that provided a thermal performance versus airflow table; for a modest airflow (quiet muffin fan) of ~700 LFM, the thermal resistance drops by about another 70%. Net result, for the 15.75 inch length option, operating with 700 LFM forced air flow, is expected to be about (1oC/W/3in * 90% * 50% * 30%) = 0.14oC/W. My heat source is distributed along the 15.75" length, rather than being a point source in the center, so I expect the actual performance to be 2-3x better (lower resistance) than the above calculation. One final note, the fins on these heatsinks are thin and quite prone to bending, especially the outermost vanes. These arrived well-packed in foam sheets inside a custom-sized cardboard boxes, and only one of the four I purchased required any straightening of the fins.

Readily machined. I used it on a resistance box that I built with four 100W resistors that takes 96.25% of the load of my 50W Marshall ORI50H and turns it into heat. It goes Marshall, resistance box, 100W L-Pad attenuator then Marshall 25th anniversary 2556AV slant cab with two Celestion Vintage 30s. The resistance box was to allow me to turn the Marshall ORI50H to full volume but be able to comfortably talk over the fully loaded JJ EL34s with the attenuator being more mid scale. Without the heat sinks, the resistance box approached 400°F, way too hot for electrical components and a burn hazard for the tolex and me. With the heat sinks arranged with the fins aligned vertically for natural aspiration, the resistance box operates below about 135°F (with the fins around 130°F) with the attenuator L-Pad more midrange, as opposed to barely being turned up.

This heatsink is really impressive for the price. I've used several different heatsinks, but when this one was first delivered, I was surprised by how clean and well-finished it was. There were no rough edges or scratches, and no blur around the edges either. A lot of Chinese-made heatsinks tend to have unfinished edges or sharp spots, but this one is exceptionally well-made. On top of that, the price is very reasonable. I'm using two of these on NVMe enclosures with thermal pads, and they do an excellent job of transferring heat. Even without a fan, the setup stays clean, efficient, and the color matches perfectly too.

私のゲーミングノートPCの電源アダプターは240wで、動画エンコードや動画のアップスケーリングなどを行い負荷をかけると、手で触れられないほどの発熱をしてて、これは良くないと思い、本製品を2つ購入。 電源アダプターの上面と下面にそれぞれ本製品を置いたところ、触っても「温かいな」くらいの温度になるまでうまく放熱してくれてます。ちょうど大きさもぴったりでした。 同じ感じで高温に悩んでる方いらっしゃいましたらこの商品はおすすめです。

Según especificaciones

Fait le job

Did the job of keeping my 3090 cooler as they run very hot