Click Here

I was skeptical about whether this relatively small shower head holder could be strong enough to actually hold my shower head wand. But the glue they included is super powerful and the holder itself is VERY sturdy even though it is small. I used their included adhesive and affixed it directly to white subway tile - and months later - it is still there as solid as can be. It looks great and functions extremely well. This was a great purchase.

This is SO much better than the suction cup holder that came with my shower head. Omg. Not only will it not fall off and make a loud noise in the middle of the night, but it just feels so solid when using it. It’s also classy, and it adjusts easily, which my other holder did not do. I got two: one for the shower head itself, and another to put near the top of the shower to route the hose for the shower head, so it doesn’t bang against the faucet. Make sure you follow the instructions properly for applying the adhesive. It’s not complicated, but it’s also not your average adhesive. You have plenty of time to adjust the position before letting it set for a couple of days, which I definitely needed to do. It’s completely worth the wait; just use your old holder in the meantime. After the adhesive dries, it’s not difficult to remove excess around the edges. I’ve been using it for a couple of weeks now, and I still feel a sense of satisfaction every time I put the shower head back in the holder, so much that I was inspired to come write this review. I’m so glad I got this thing.

The original shower head holder would not stay kept falling down. It was one of those suction ones. So I ordered this one. It is very sturdy easy to install and it is working for my shower

I GOBBED the stuff on the back cleaned around it and left it taped up for like 4-5 days to make sure it was dry because I still showered 2 times while it was up. The humidity could slow down drying but I only have one shower. Gently using it and not being rough I'm just thankful to have somewhere to hold my showerhead low. Finally 🙏🏼

Easy install well made. Looks good and just the right size. Good color match. Stays where you aim it.

Being a short person I could not reach shower wand in its original installed position. I needed polished brass and couldn't justify cost of adjusted rail installation. These are an amazing quality and value. They are very sturdy and when installed, appear as though they are an original installation. I noticed the glue was from Germany, so I felt more positive about its ability to stick forever. Easy to install. I like the fitted sticky tape which holds it in place for the recommended amount of time for glue to dry. Glue also gives time to adjust and level. Recommended wait time is 48-72 hours. I gave it the full 72. Excess glue was easy to scrape off tile. FYI. I purchased two. One at a height for washing hair, and at about a foot lower I placed the other at a height for showering without getting hair wet. I am so thrilled with them. Super quality brass and construction. Easy to adjust after installation by moving wand. No more crashing down suction holders and wand in the middle of the night

This shower head holder is well made and is all metal vs plastic used in other holders. I particularly like the tight ball joint, as I have a heavy shower head and it will hold it in place. It has to be glued on and then held in place while it dries from 48 to 72 hours. It comes with light weight adhesive strips to hold it in place while the glue it drying, but I opted to hold it in place with duct tape (see attached picture). Now I know that when I peel off the duct tape in 72 hours, the shower head holder will be solidly adhered to my wall. I also found when I screwed of the cap on the tube of glue, I could not squeeze out any glue, so I just snipped off the top. The glue is light a paste, making it easy to work with and, even though it came with two tubes of glue, I only needed to use one. Be very careful to place the glue only where the pictured instructions tell you, as putting glue in the center of the adhesive plate will lock in the rotating ball. Also only put the glue on in small dabs, as too much glue will also lock up the ball rotating ball.

I had the plastic mount that came with my oxygenics showerhead. I wanted to get a shorter hose, and they are easily available, nice stainless ones, but they don't fit the oxygenics holder, which is too large. All other holders, like this one, are a 'standard' size. Most holders I found have the cradle attached to the shaft at 90-degrees, which severely limits the range of motion and allows moving the showerhead in nonsensical directions. This one is angled, which means the showerhead can be adjusted to point straight or downwards. It has a nice brushed stainless finish. The ball-mount holds firm and moves smoothly. Very nicely made. It can't be tightnened, but seems like it is well made and will stay put and not sag. It is provided with a mastic adhesive, which must be cured for 48 hours. Since the plastic showerwall was not attached to the wall, I found that the adhesive is not enough, so I drilled 2 holes in the corners, and screwed into the wall. Solid. I also applied silicone around the top edge, so no water could get in to loosen the glue. Very happy.

High quality product

El pegamento que trae no funciona, solo se mantuvo pegado 3 días y se cayó. El producto como tal se ve de buena calidad pero el pegamento no.

Tien très bien et belle apparence

excellent adhesion to ceramic shower stall,easy to reposition shower head while in wand bracket. metal bracket,not plastic.excellent quality.

Exactly what o ordered