Delkin Devices Fat Gecko Dual Suction Camera Mount (DDMOUNT-SUCTION), black 3.5 x 9.5 x 11.3 inches

I own two Fat Gecko Triples and one Fat Gecko Single. One of the best features about the Fat Gecko System is that it's modular and can be built onto and adjusted to meet a variety of needs.The Fat Gecko Triple says that it's a combo of the Double and a Single, which isn't exactly true. If you buy a Single separately, it also comes with a flash bracket and a plastic extension that adds a few inches of reach to the arm. These items do not come with the Triple. However, one thing the Triple does include (that isn't included with the Single or Double) is an aluminum clamp which mounts on the extension bar of the Double. The clamp is used to combine a Single with the Double to make the Triple. Feel like I'm taking about baseball. Anyhow, if you add the cost of the Double and Single, it's close to the cost of the Triple, but I suppose the savings is that you get the clamp with the Triple, a part that costs $20 by itself.As for the build quality, I find it to be very good. The pictures and description do not give this product justice. All the knuckle joints are made of metal. The twist locks are made of metal. The twist collars are made of metal. I'm not sure about the type of metal, but it doesn't appear to be the cheap pig iron that you find in many low quality parts. The ball joint is definitely steel as are the threaded posts (that hold your expensive gear). All the plastic that is used is a higher grade plastic than what most cheap Made in China products use. It's similar (if not the same) as the plastic used in Nikon and Canon products. As for other construction, the swivel where the suction cup mounts has click stops and washers and the clamps that tighten down over the balls are grooved to ensure a tight, slip free grip.Now, for why I feel Fat Gecko exceeds other similar products. It's so ridiculously modular that you could build just about any configuration you could imagine (limited by how many sets as you want to purchase of course). When buying the Triple, you actually end up with a Double and Single. But, when I purchased another Triple, I found that I could make a Quad setup for maximum stability, and then had two Singles left over. All the parts interchange on all of the sets and Delkin also makes other products in the Fat Gecko line. I do not know about the whole line, but parts from the surface mount system can also be used with their Gator Clamp system as well. Along with the modularity comes maximum flexibility for adjustments. Many flat surface mount systems I've seen and researched would need a flat surface with all suction cup being on the same plane. Most can only mount two of three cups on something with as little curvature as a car hood. The Fat Gecko system has so many adjustment points that can be positioned in so many angles, I can't imagine many applications where a way to mount it, or the desired angle couldn't be found.I'd say the fail point on most suction cup based systems would be the suction cups. Cuts, holes or other damage to the cups basically renders the entire system useless. Most systems I've looked at do not have a fix for this. On many, the suction cups are attached to the frame. Damage one cup and you'd just have to throw everything away. Even the most expensive systems offer no way to replace a suction cup. Now, Fat Gecko doesn't market the Stealth model as a replacement suction cup, but that's what it could be. For $20, you can buy a complete suction cup replacement that is easily exchanged for a damaged one.The operation of the Fat Gecko is very simple. Just attach the suction cups fist, then adjust for angle and tighten down the clamps. Just remember to tighten all the clamps. The suction cups have a feature not found on most (even expensive sets) flat surface mount systems. A large button labeled "Press" is on top of the suction cup. Pressing the button forces air out of from under the cup. To finish securing the cup, a latch is lifted that locks it down. To remove the suction cups, just push down the latch and pull up the tabs on the sides. I've actually had the cups so secure that I've had to almost pry them off the surface.I've tested this system in several settings with different mounting configurations and can confidently say that I have no problem trusting my $4,500 rig to this product.The description says that some of the fittings are rubber to help minimize vibrations. I feel this is pretty much hype. Yes, there are runner O-rings at several connection points, but I feel their effect is negligible. However, regardless of the O-rings, this system is extremely stable (well, at least using three suction cups for mounting). One reviewer stated the Single was worthless for mounting a camera. I would not recommend mounting a DSLR on a Single, however a GoPro or anything of relative size shouldn't pose much of an issue. I use the Singles/Double for mounting lighting, mics, etc, so shake isn't an issue in those applications.I read some other reviews with complaints about mounting on various surfaces as advertised by the manufacturer. I think there's a little ambiguity in the advertising, however maybe some user error in not fully understanding the limitations of this system. For one, the manufacturer clearly states that these systems will easily mount to any smooth, flat, non-porous, surface. These surfaces include windshields, car hoods, surfboards, helmets, etc. I think some issues that people have had is that they've mounted (or tried to mount) one of these rigs onto something that they thought was smooth, flat and non-porous, that actually was not. One reviewer had mentioned mounting a camera to a surfboard, only to lose everything in the ocean. The thing is, most surfboards I've seen do not have a smooth surface. Yes, most are flat and non-porous, but most I've seen are also textured. Textured in that they have small bumps, usually designed to increase traction. However, I'm sure there are boards out there that have a smooth surface. I just find it hard to believe (given my experience) that a properly sealed suction cup on a smooth surface surfboard couldn't hold the weight of a GoPro during the first wave. Also, I'd never mount anything to a car, cycle, surfboard, etc without using a tether. The issue I have with the cycle helmet claim by the manufacturer isn't that it's not true, it just may not be possible with a variety of helmets or more probable, probably not the view/angle you were hoping for. The picture on the packaging shows a Fat Gecko Single mounted to the side of a helmet. I've owned several helmets and know that due to the nature of design, the sides are longer and flatter (well, less round) than the rest of the helmet. Having ridden cycles for years, I personally would not want even a couple ounces of uneven weight on one side of the helmet. Not only that, but who'd want the whole right (or left) side of their recording to be obscured by the helmet. The best placement is the top center or back center of the helmet. Not currently owning a helmet, I haven't been able to test the mounting ability of the suction cups, but I think there's some validity to any issues people may have had with helmets. I'd say the marketing dept at Delkin ride.Well, that's pretty much it. A great product that works fantastically for everything that I need it to do. I only gave four stars, because I think being manufactured in China, the whole Triple (which sells for $99) probably costs about $9 to produce. I guess the mark up comes from the photos of the product mounted on helmets and such. Could be priced a little more appropriately I'd say. Also, I'm no rubber specialist, but I'm not sure if the rubber used for the suction cups is of the highest quality or not. I'm on the fence about that, as I've seen the black, denser rubbers that seem to last longer, but possibly don't have the same tack and grip as the clear rubber, which seems to wear (and color) faster. And that's all I have to say about that.

I was hesitant to purchase as the glass surface of the planes at my school is no where near flat,I’ve used a ton of different mounts as space is limited in planesIncluding ram and pivotPivot is the number imo 1 but you are stuck using their case and it costs over 200$ for the case and mount setThis one id rank second after pivot as it’s not as light or as small as the pivot but it falls off a lot less than the ram does in abrupt turns or hard landings and it half the priceI was debating on getting the double suction mount but the single has zero issue holding itself on the curved glass of the windshield and the tablet holder grips perfectly no issues holding perfectly still, very easy to put in or take out the iPad mini I use without having the worry about accidental button pushes

I was using this for mounting a 360 camera to the top of my car to upload my own 360 streetview videos!Suction is really good, and I never felt like it would easily fall off. If you have the money, you probably shouldn't risk an expensive camera with only one suction cup, but I'm broke so I just got the one suction cup.

Solid, manageable, very adjustable, suction works well on the windshield.

I had this stuck on my car for a month to help replace a broken side mirror. Held great and didn’t fall off

Suction is good, But ball head does not hold 360 insta camera with a extension. Cameras must be attached directly to the product without using any type of extension.

I was looking for a good 3 cup mounting solution for my Insta360 X2 to safely mount to my car.Originally went with some other brands due to cost, each having issues not being able to hold the pole securely enough to stop it from dropping from the weight of the camera while hitting bumps in the road. Several times I almost lost my 360 due to this.So I decided to finally try this solution, and am kicking myself for not buying it from the get go.It's not only more stable, the cups are a lot better as well. The swivels and clamps get a much firmer grip and do not let the pole drop at all. Even after hitting large bumps. I feel this is a MUCH safer option for mounting a 360 camera to a vehicle.

I bought this about year ago and really love it

Would totally recommend this for any social media or car enthusiasts who want incredible shots!! I do have a drone I use also but this dynamic cinematic shots you can capture with this unit is incredible. I have found not many who have tested this for a speed/wind rating. I can ensure you I have had this over 120km/hr with a $1000 camera and was nothing but confident. However if you are using a selfie stick do not fully extend as I find it does slide down with wind. I have a single mount camera but would not recommend it for external use. Follow the instructions clean surface always and suction cups and never store them in a hot area or too cold . My other tips always make sure everything is tight . Awesome product

gör vad den ska

He probado muchísimos sujetadores para mis diferentes cámaras, de todos este es el mejor, por su calidad, precio, algunas piezas son de plástico y otras de fierro, pero cada pieza es de buenos materiales. Lo uso para el coche y sostiene muy bien las cámaras, además de que es muy versátil con las diferentes posiciones en las que se puede usar.

Además del excelente precio, el artículo supero mis expectativas, la succión es fuerte y se siente muy seguro para montar el equipo, se pude desensamblar para utilizar de forma individual una, dos o las tres ventosas, según las necesidades de montaje. El material ligero y resistente. Lo recomiendo.

La base fue demasiado grande para mi caso de moto, el diámetro es de 8.5 cmel material y el agarre en superficie plana es bueno