Better Living Products, White 76354 Euro Series TRIO 3-Chamber Soap and Shower Dispenser

LOVE LOVE LOVE!!! Paranoid at first because of the 5 star and also the 1 star reviews. I ordered 2. One came damaged but I got it replaced. I got the white with silver knobs. Thought it'd be a little bigger..... each slot holds 14 oz. But after using it, very pleased. It comes all in one piece with double stick tape and silicone adhesive along with over 12 labels that say shampoo, conditioner, shower gel etc, that you adhere yourself so you can have your soaps in the order you like. It seems like a no brainer but I must stress READ THE INSTRUCTIONS. It looks like you'd slap on the tape/glue pop it on your wall and fill it so I get now the comments about it falling off the wall and breaking. You have to detach the container from the mounting bracket and adhere that to a clean (and alcohol wiped) surface. The bracket has all these little holes that some of the silicone glue oozes through when you press it to your shower wall allowing it to kind of suction and you can't achieve this with the container attached to the bracket as it is when you pull it from the box. Nor will the glue dry properly so I see now why people had it popping off. I attached it to a slick suface as well as a tectured surface. I could not budge it pulling very hard. Which I tested because I was worried about mine falling off the wall per some reviews. Because it is breakable, put it somewhere safe or back in the box while the glue dries on the bracket. There was a comment about thick conditioner/shampoo not dispensing or leaking (Again instructions) I'm a cosmetologist, my conditioner is thicker than mayonnaise. It has no problem coming out and I've had no leaks. You have to prime the pumps and again if you completely empty it. This is done by first depressing the button and holding it in then with another finger, cover the spout. Then pump fast ten to twelve times (the spout will suction to your finger) break the suction by pulling your finger off the spout and repeat the process until you can no longer cover the spout without product coming out as you pump it. Takes about three trys. The only thing that is very mild concern is the amount that comes out isn't much, however, the first washing isn't intended to lather anyway. People waste so much product thinking this. The first wash the soap adheres to the dirt/oil/hair dye and shouldn't lather, rinse and repeat, it will lather the second time and you'll use so much less soap and save money. That's why we wash your hair twice! But I use lots of conditioner so its quite a few pumps. But I use less and so do my kids with less mess and less waste. It's fun to fill with different colors too since its see thru. No bottles cluttering up my showers or my kids using a whole bottle to make bubbles or whatever other excuse they using for dumping a whole bottle out. Love this thing! I will never own a shower without it! I want to buy one for everyone I know!

I hate it when people fail to read the instructions, have a bad experience, and then give a product poor reviews. No seller should be negatively impact of by your stupidity. That being said, the instructions are a bit though to follow, because they appear to be the result of Google translate, and were clearly not written by an English speaker. So, here you go: 1) remove the plastic mounting plate. Use it to figure out where in the shower you'd like to mount this. If you plan to hang with screws, level the unit and Mark your drill holes. Attach the mounting plate with screws, hang the unit, and skip forward to step 6. 2) If you plan to hang this with adhesive, mark the location you want to hang your mounting plate. Clean all surfaces thoroughly. 100% acetone works best, as it will remove all surface oils, residues, etc. However, acetone may damage some surfaces, so use rubbing alcohol instead if you are unsure. 3) on the four flat surfaces, attach the four double sided pads, but do not remove the protective film on the side facing away from the unit. Take the tube of silicon, cover the entire surface of the back of the mounting pad with silicon. Use the entire tube. Remove the protective film from the sticky pads. Carefully align the mounting pad where you intend for it to be mounted. Check to see if everything is level, then press down on the mounting pad until silicon starts to ooze through the little holes. 4) Walk away. The silicon needs 12-24 hours to cure. If you can avoid it, do not use that bathroom. Moisture may impact drying time and adhesion. 5) attach the dispenser. It should slide and lock into place fairly easily. Fill your dispenser bottles and replace the top lid. 6) PRIME THE UNITS! Before first use, you need to prime each of the dispenser pumps. To do this, rapidly pump the button until you get a healthy flow of product. Without priming, you'll get a slow trickle, and might not get any product at all. If you follow the instructions and prime your unit, you'll have no trouble. Mine have been up for more than a year now. They dispense fine, don't clog, and have never fallen off the wall.

Perfectos para no tener nada en el plato de ducha. He comprado dos y llevan más de 2 años.

This is the third one I have had in my shower room, only replaced due to revamps. So tidy no bottles everywhere

Parfait. Le mien, acheté il y a au moins 20 ans avait fini par fuir. Le remplacement à l'identique était essentiel pour moi. C'est fait... J'espère qu'il durera aussi longtemps que son prédécesseur.

Very good quality dispenser - easy installation.

We love this dispenser as this helps us declutter our bathroom. It sticks properly if you follow the instructions. We have been using it for quite sometime now and it’s still there and the dispensing part is really good as it does not waste any.