AnzoUSA 111183 Chrome Projector Halo Headlight with Side Marker and Parking Light for Ford F-150/F-250/Bronco - (Sold in Pairs)

I love ANZO USA products but they dropped the ball on this one I was expecting to get LED projector lights not some cheap H1 & H7 halogen bulbs the only LED's on the whole assembly were accent lights100% easy installLook greatPoor out of box light quality my LED turn signal bulbs are brighter than the headlights are even with high beams onNow I am ordering new LED headlight bulbs that I would have preferred to know I needed before installOn 1992-1996 Ford F150 Adjustment screws are NOT accessible after installation lights have to be taken out to adjust up and down huge inconvenience

I had these headlights on for about two and a half months so far and I really like them, it gives my truck a fresh look since my stock headlights seal was going bad and there was lot of moisture inside of it. They weren't that hard to install except for having to remove my battery and washer and radiator reservoir a couple times. But there's only one thing I don't like and one thing I'm bummed but its a minor. The one I don't like is that there's only one adjustment screw, as far as I know, for both low and high beams so when my low beams are leveled, one high beam go into the sky and the other aims slightly lower than where my low beams are aimed and vise-versa so I'm at a los right there. The thing im bummed about is that I wish I could fit my chrome bezels over the black since my truck is bright red and white, it makes my truck look like it has glasses lol, but I still love the headlights. I'm going to try and modify my old chrome bezels to see if I can fit them over it, but if I can't its not a big deal, I just think with my truck being bright red and white the chrome would look better then the black. I could've went with headlights that did't have a bezel around it, but they didn't look as good as these. But other than those two things the headlights are really great and improves my visibility greatly too but will replace stock bulbs that came with it with a little more brighter ones.

Pretty simple to install. They are very bright and make my bronco look amazing. I never had to adjust them but it does seem like it would be a pain if I needed to.

Well I'm not going to lie. These things aren't perfect and need a good bit of modification to get where they should be.1) The beam height adjustment are totally unacceptable. Even when adjusted as high as they can go beam is dangerously low and does not allow the light from the headlight to travel down the road adequately. I was driving down a dark country road and was startled by a someone riding his bicycle on the shoulder. I was driving within the speed limit and was paying full attention but the light didn't hit him until he was about 40-50 ft away. That's a problem when I'm doing 40 mph and he's doing 7-10mph. To correct this I had to install spacers/washers on the bottom 2 studs to raise the beam to an acceptable and safe angle.2) the use of halogens light bulbs (like the ones that comes with these headlights) aren't advised. They are not nearly as bright as you need or want them to be in any situation i can think of. To correct this I recommend going with 50-55W HID headlights. I installed a good/cheap set from DDM Tuning and the difference is literally night and day.3) the turn signal / running lights bulb which comes with the headlights are amber and are "just okay". Because I went with HID headlights I figured I'll go with White/Amber Switchback LED bulbs for these. When the running lights are on they are white but when the turn signals are engaged they flash amber. No resistor was needed.Those were the only real issues or upgrades that I needed to address to get these headlights in the form and function that I thought they should have been right out the box. The other lighting effects in there are weak and cheesy to be completely honest. They could have utilized cold cathode neons for the halo and two light bars at the bottom (which would have really looked awesome) but I guess the extra $5 in manufacturing costs was a bit too much when your #1 goal is low costs and not necessarily quality.I also don't have high hopes that the clear polycarbonate used on the entire face of the headlight will hold up for years without dulling, fading or showing abnormal signs of wear. You could put some form of clear film protectant over them maybe (like they have for cellphones) but I'd do that soon after install rather than wait if you wanted to go that route.I have yet to notice any condensation within the housing but there are stickers on the lights to address this if you do which basically states that condensation does not equal a leak.Some ppl have complained about the gap at the bottom of the housing. To be honest I think the gap was always there but it wasn't noticable because the original headlight housing is in chrome and that masks the gap pretty well. Where as these headlights are all black and does not. In truth the gap is hardly noticeable on my truck.Hope this helps!

The assembly fit well, one high beam light didn't work but purchased new bulb which fixed the problem. Anyways I'm happy with the item if it didn't come with a faulty bulb I would have given it a 5 star rating not worth sending the assembly back over a light bulb.

Fit, look and work great.

Headlight assembly looked great and was easy to install, but could not set low beams safe enough to drive at night

Se ve chingona mi troca con esos focos. Los recomiendo. Me encantaron