Winjet WJ30-0629-09 Replacement for 2018-2019 Subaru WRX Front Clear Fog Light Pair Wiring Kit Inculded

Just installed and could not be happier, the quality is great and comes with all the hardware very neatly packaged. I strongly suggest getting the factory “Y” harness, button, relay, and replacement panel where the button goes. Whole project took me about 20 minutes. And was much cheaper than buying it as a kit from Subaru.

100000% recommend this kit. I replaced the halogen bulbs with led bulbs. I also used the pre-wiring that the 2018+ come with. To do so, I ordered these parts and threw out the wiring/fog light button that came with this set. You can find videos of install on YouTube by searching “18 wrx OEM fog light install”. New harness to add fog function: part # 848981VA010 (x2. One for each side) Relay (connected behind glovebox) part # 82501AG041 Fog light switch / button part # H4510FJ000 New panel (has cutout to use new switch) 2015 is part # 83472FJ010VH 2016-2019 is part # 83472FJ070VH OEM kit sells for over $300 and this kit plus the parts above were about $200 and done the CORRECT WAY! Install was straight forward. Enjoy!

Produce is good and fits. I did not use the wiring harness though. I just used the lights and bumper covers but they fit and worked.

Since I work at a dealership, I get parts at cost. However, I ordered this as a way to test an alternative so I can provide it as some advice to friends or customers looking for a cheap alternative. What I can say is this: The harness and switch included really overcomplicate things. Throw those away. The 2018+ has a harness built in. You can purchase a relay, switch, and the only remaining wiring needed from a dealership’s parts department for not very much. Buy those items, and use the bezels and lights included in this kit. Installation with this method takes only about 20 minutes. Here’s how. -Lift the car -Pop the clips out of the two undershields below each fog lamp. -Unplug the wire from the blinker. -Unplug the stock blinker harness from the body harness -plug in the new harness. -screw in the fog lights -plug the lights and blinkers back in to the new harnesses. -remove the panel with the traction control and trunk pop switch -snap in the oem switch. Plug that in to the remaining plug already included on all stock models -plug in the relay behind the glove box -snap the bezels In on the bumpers Once that is done, you can just toggle them off and on as you normally would. The switch will light up, and it will indicate on your dash as if oem. The figment is excellent. To most untrained eyes, it will look like there is a gap and the figment is wrong, but the same can be said for the OEM kit, or limited models that already have fog lamps installed. The plastic bezels are identical to the OEM in terms of fitment and quality. Tl;dr: toss the bootleg wiring harness, spend the extra bit of cash, and buy OEM. Then the off brand lights and bezels will function and look JUST like the OEM counterpart at a fraction of the cost.

Worked and fit perfectly. You get exactly what they say and it is easy to install.

Very easy to take out

Easy installation. Wish could let us choose color switch light.

Installed these. I knew right away that the fog light housing was not sturdy quality. OEM fog lights are glass lenses with a very thick plastic/ABS housing. These are very thin plastic for the lens and housing. My first extended road trip of approximately 2hrs (100 miles), the front lenses are already melted and plastic bubbled up on the inside of lens due to heat from bulb essentially boiling it. Had to disconnect the harness from fog lights before next weekend road trip causes fire and complete meltdown. And I am using some unusually intense heat producing bulb. Just the usual HID hyper white bulbs. Buy OEM or better quality.

Just installed this in a base 2018 WRX , as some previously mentioned , throw away the wiring kit and switch and purchase the two harnesses, relay and OEM switch as well as the four shoulder bolts and "J" clips from Subaru ... it makes for a cleaner install and you have all the features of a factory installed system. As for the foglights themselves, they are cheap plastic with a plastic lens and the bezels fit but they leave a 1/4 inch gap to the lights.The tabs are fragile so don't test fit them too often because you will break some tabs off ... i broke one but it was in a position that didn't hamper the fit. The foglights will need to be adjusted after installation, they are not preset ...